Deleting Images And Videos - MolecuLight i:X Manual Del Usuario

9.6 Zooming in and out and Panning
9.6.1 Zooming in and out
To zoom in and out on a displayed image:
1. Select the image. The image will fill the full screen.
2. Place your thumb and pointer finger at opposing points of the image.
3. Keep both fingers on the screen and gently move your fingers away from each other.
This action "zooms in" on the part of the image between the two fingers, enlarging the portion of the image between
the two fingers.
Note The speed at which your fingers spread influences the rate of zoom.
4. To zoom back out, reverse the motion and gently "pinch" your fingers towards each other while keeping contact with
the screen.
This action "zooms out" on the part of the image between the two fingers, reducing the display of the portion of the
image between the two fingers.
Note It is not possible to zoom in and out on video recordings.
9.6.2 Panning
To pan a displayed image:
On a zoomed in image, drag the screen with one finger to move around the image or hold your finger near the edge of the
screen to pan to that side. Move your finger closer to the edge to pan more quickly.
It is only possible to pan a displayed ST-image or FL-image that has been zoomed. It is not possible to
Note
pan a recorded video. It is not possible to pan during image capture.

9.7 Deleting Images and Videos

To delete an image or video:
1. Select the image or video on the Display Screen.
2. Tap the Trash icon.
You will be prompted with "Allow 'iX Camera' to delete this photo?" or "Allow 'iX Camera' to delete this video?"
3. Select either 'Don't Allow' or 'Delete'.
Selecting 'Delete' will delete the image or video.
Images are not permanently deleted using this method. Images can still be recovered on the device
Note
from the deleted images folder.
9.8 Charging MolecuLight i:X
The Display Screen and the MolecuLight i:X Imaging Device each contain a rechargeable battery. Both batteries need to be
charged separately in order for MolecuLight i:X to work properly. The cables for charging both batteries are provided as one
item (MolecuLight Power Cable) so that the MolecuLight i:X Imaging Device and Display Screen may be charged
concurrently. Geography-specific MolecuLight Power Cable Adapters (supplied) may be required to connect the
MolecuLight Power Cable to the wall outlet.
TM
MolecuLight i:X User Manual Revision 1.0
9.8.1 Charge the MolecuLight i i :X Imaging Device
To charge the MolecuLight i:X Imaging Device:
1. Connect the MolecuLight i:X Imaging Device to the black power supply cable on the MolecuLight Power Cable (P/N
1142) as in Figure 18. The black power supply cable charges the MolecuLight i:X Imaging Device.
The MolecuLight i:X Imaging Device begins charging. The Battery Status LED indicates the battery power as described in
Section 6.1.1.4.
2. When the Battery Status LED is solid green and no longer blinking, disconnect the MolecuLight Power Cable from the
wall. Then remove the black power supply cable from the device and store the MolecuLight i:X for its next use.
Note
Note
Note
9.8.2 Charge the MolecuLight i:X Display Screen
To charge the MolecuLight i:X Display Screen:
1. Connect the white connecting cable on the MolecuLight Power Cable (P/N 1142) to the port on the MolecuLight i:X
Display Screen as shown in Figure 18.
2. Connect the USB power adapter to the other end of the white connecting cable as shown in Figure 18.
3. Plug the USB power adapter into an electrical outlet.
4. When the battery status on the Display Screen indicates that it is fully charged, disconnect the MolecuLight Power Cable
from the electrical outlet and then remove the MolecuLight Power Cable from the device.
Note
9.9 Uploading Images and Videos to Computer
You can upload images and videos to a computer using supported applications on your Mac or PC.
To upload images and videos to a computer:
1. Connect the white connecting cable on the MolecuLight Power Cable (P/N 1142) to the port on the MolecuLight i:X
Display Screen. Connect the USB connector end of the white connecting cable to your computer as shown in Figure 19.
When prompted to 'allow' or 'trust' the computer on the MolecuLight i:X Display Screen, you may do so.
Communication between MolecuLight i:X and your computer will be established automatically.
Note
2. Do not use iTunes to copy or move images from MolecuLight i:X to your computer. If you have iTunes on your
computer, you will automatically be prompted to access the images/videos via iTunes.
Page 29 of 43 MolecuLight i:X
Figure 18: Charging MolecuLight i:X Imaging Device and Display Screen with MolecuLight Power Cable
Connection to wall outlet should be easily and readily accessible and not blocked when MolecuLight i:X
requires charging.
MolecuLight recommends charging the MolecuLight i:X whenever it is not in use so that it is fully charged
for its next use.
It takes up to 5 hours to fully charge the MolecuLight i:X once it is fully depleted. It takes approximately 2
hours to charge to 80%.
MolecuLight recommends charging the MolecuLight i:X Display Screen whenever it is not in use so that it
is fully charged for its next use.
If the USB connector end of the white connecting cable is connected to the USB power adapter,
disconnect it.
TM
User Manual Revision 1.0 Page 30 of 43