Tabla de contenido
EN
Setting up your machine
DANGER: Never leave the machine unattended when plugged in. Always
Bu sure to wipe off any surplus oil from needle
unplug this machine from the electric outlet immediately after using and before
plate area before using your machine the first
maintenance. WARNING: Do not unplug by pulling on the cord. To unplug, grasp the
time.
plug, not the cord. When foot control is disconnected, the machine will not operate.
Power line cord/foot control
Make sure that the sewing machine is turned off (the
power switch is set to "O"), and then connect the plug
of the power line and into the appliance inlet and your
FOOT CONTROL
wall outlet.
Sewing speed can be varied by the foot control.
Sewing speed can be varied the foot control.
The harder you press on the control, the faster the
The harder you press on the control, the faster
machine runs.
machine runs.
When foot control is disconnected,
NOTE:
the machine will not operate.
KNOWING YOUR SEWING MACHINE
CONVERTING TO FREE-ARM MACHINE
KNOWING YOUR SEWING MACHINE
Converting to free-arm sewing
Always disconnect the machine from power
Your machine can be used either as a
supply by removing the plug from the wall-outlet.
flat-bed, or as a free-arm model. With the
Your machine can be used either as a flat-bed or as a
Converting to free-arm sewing
extension table in position, it provides a
Power/light switch
free-arm model.
working surface as a standard flat-bed
With the extension table in position, it provides a
Your machine will not operate until the power/light switch is turned on. The same switch controls
model. By removing the extension table (just
Your machine can be used either as a flat-bed or as a
large working surface as a standard flat-bed model.
both the power and the light.
free-arm model.
pull it off to the left as shown), the machine
To remove the extension table, hold it firmly with both
When servicing the machine, or changing needles, etc., machine must be disconnected from
With the extension table in position, it provides a
converts into a free-arm model.
hands and pull it off to the left as shown. To replace,
the power supply.
large working surface as a standard flat-bed model.
slide the extension table back into place until it
To remove the extension table, hold it firmly with both
clicks.
hands and pull it off to the left as shown. To replace,
With the extension table removed the machine
slide the extension table back into place until it
converts into a slim free-arm model for sewing
PRESSER FOOT LIFTER
clicks.
children's clothes, cuffs, trouser legs, and other
With the extension table removed the machine
hard-to-reach places.
There are three positions for your presser foot:
converts into a slim free-arm model for sewing
1.
Lower the presser foot to sew.
children's clothes, cuffs, trouser legs, and other
Presser foot lifter
2.
Raise the lifter to the middle position to insert or
hard-to-reach places.
remove fabric.
There are three positions for your presser foot.
Presser foot lifter
3.
Lift it to its highest position to change the presser
1. Lower the presser foot to sew.
foot or to remove thick fabric.
2. Raise the lifter to the middle position to insert or remove
There are three positions for your presser foot.
fabric.
1. Lower the presser foot to sew.
3. Lift it to its highest position to change the presser foot or to
2. Raise the lifter to the middle position to insert or remove
remove thick fabric.
fabric.
3. Lift it to its highest position to change the presser foot or to
remove thick fabric.
Reverse sewing lever
As long as you are pressing down this
Reverse sewing lever
button while sewing, the machine will feed
66
the fabric backwards.
As long as you are pressing down this
button while sewing, the machine will feed
6
Power/light
switch "OFF"
Texi Fox 25
4
5
7
8
Power/light
switch "ON"
1
1
9
3
3
2
3
2
Capítulos
Tabla de contenido
