Tabla de contenido
eading the machine
KNOWING YOUR SEWING MACHINE
EN
e take-up lever to its highest position
rning hand wheel toward you. Raise
Threading the machine
5.
Draw the thread through
ser foot.
Threading the machine
take-up lever from right to the
e spool on spool pin as shown, with
left (3).
Raise take-up lever to its highest position
d coming from the back of the spool.
Raise take-up lever to its highest position
by turning hand wheel toward you. Raise
6.
Then draw thread down (4)
by turning hand wheel toward you. Raise
presser foot.
and slip it into the lower
presser foot.
Place spool on spool pin as shown, with
thread guide (5).
Place spool on spool pin as shown, with
thread coming from the back of the spool.
7.
Thread needle eye from front
thread coming from the back of the spool.
aw thread into thread guide using both
to back (6) and pull thread out
ands.
under the presser foot about
aw thread down into the tension area and
10 cm.
ound the check spring holder.
1. Draw thread into thread guide using both
1. Draw thread into thread guide using both
hands.
rmly draw thread up and through take-up
hands.
2. Draw thread down into the tension area and
ver from right to left.
2. Draw thread down into the tension area and
around the check spring holder.
around the check spring holder.
hen draw thread down and slip it into the
3. Firmly draw thread up and through take-up
3. Firmly draw thread up and through take-up
wer thread guide.
lever from right to left.
lever from right to left.
o not block the thread into double needle
4. Then draw thread down and slip it into the
4. Then draw thread down and slip it into the
ring.
lower thread guide.
lower thread guide.
aw thread down and slip it into needle bar
5. Do not block the thread into double needle
5. Do not block the thread into double needle
spring.
read guide.
spring.
6. Draw thread down and slip it into needle bar
read needle eye from front to back.
6. Draw thread down and slip it into needle bar
thread guide.
: Cut the thread end with sharp
thread guide.
7. Thread needle eye from front to back.
scissors for easier needle threading.
7. Thread needle eye from front to back.
Note: Cut the thread end with sharp
Note: Cut the thread end with sharp
scissors for easier needle threading.
scissors for easier needle threading.
n needle
TWIN NEEDLE
Twin needle
Twin needle
to thread the double needle:
How to thread the double needle:
1.
Thread the left needle in the
1. Thread the left needle according to the
read the left needle according to the
How to thread the double needle:
same way as you threading
way of threading single needle from step
ay of threading single needle from step
1. Thread the left needle according to the
single needle from step one
one to step five, then fix the thread into
e to step five, then fix the thread into
way of threading single needle from step
to five, then fix the thread into
the double needle spring as point 5 in the
e double needle spring as point 5 in the
one to step five, then fix the thread into
right picture. Draw thread down and slip it
the double needle spring as
ght picture. Draw thread down and slip it
the double needle spring as point 5 in the
into needle bar thread guide 6. Finally
shown on the illustration (5)
right picture. Draw thread down and slip it
o needle bar thread guide 6. Finally
thread into the left needle eye from front
and slip it into the needle bar
to back.
into needle bar thread guide 6. Finally
read into the left needle eye from front
thread guide (6). Thread into
2. Thread the right needle according to the
thread into the left needle eye from front
back.
the left needle eye from front
way of threading single needle from step
to back.
read the right needle according to the
to back.
one to step nine.
2. Thread the right needle according to the
ay of threading single needle from step
2.
Thread right needle in
way of threading single needle from step
Note: Be sure to thread the left needle
ne to step nine.
standard way.
one to step nine.
thread firstly then thread the right
NOTE: Thread the left needle
needle thread. Put the thread spool
: Be sure to thread the left needle
on the spool pin, make sure that the
Note: Be sure to thread the left needle
thread firstly then thread the
thread firstly then thread the right
left thread will run anti-clockwise,
thread firstly then thread the right
right needle thread, so to avoid
the right thread will run clockwise.
needle thread. Put the thread spool
needle thread. Put the thread spool
on the spool pin, make sure that the
the condition that the bobbin
on the spool pin, make sure that the
left thread will run anti-clockwise,
left thread will run anti-clockwise,
cannot put into the spool pin.
the right thread will run clockwise.
the right thread will run clockwise.
70
KNOWING YOUR SEWING MACHINE
1
3
1
3
1
3
2
4
5
6
7
2
2
4
5
4
5
6
7
6
7
1
1
1
3
3
3
Left needle
thread
1
3
1
3
1
3
4
2
7
2
4
5
4
5
6
6
7
8
7
8
Texi Fox 25
2
2
2
6
6
7
6
7
7
Right needle
Right needle
Left needle
thread
thread
thread
Right needle
Left needle
thread
thread
2
5
6
8
4
5
4
4
5
5
5
6
5
5
6
6
7
7
7
Capítulos
Tabla de contenido
