1. TRUCK DESCRIPTION
1.1. Application
The truck is designed to transport goods on level surfaces. It can lift open bottom or diagonal
board pallets as well as roll cages that extend beyond the area of the load wheels. The truck
is designed to be used in conditions with an ambient temperature of between 5°C and 40°C.
If the truck is kept in an environment where the temperature is less than 5°C for an extended
period of time, for example, in cold storage or in conditions with extreme fluctuations in
temperature and humidity during the use of pallet, you must install additional specialised
equipment and obtain permission from the manufacturer.
1.2. Assemblies
A170148 (EPT20-15HJ)
Item
Component
1
Control handle
2
Control shaft
3
Controller cover
4
Pump
A170149 (EPT20-15ET)
Item
Component
1
Control handle
2
Control shaft
3
Controller cover
4
Pump
1.2.2. Key switch (optional)
Switches the control current on and off.
Power supply to the truck is cut when the key is
turned to «OFF».
Power supply to the truck is switched on when
the key is turned to «ON».
Removing the key prevents the truck from being
switched on by unauthorised personnel.
1.2.3. Battery discharge indicator
A170148 (EPT20-15HJ)
When the truck has been switched on via the key
switch, the battery charge status is displayed.
The colours of the LED represent the following
conditions:
- When the battery is fully charged, the first LED
lights up. As the battery charge decreases, the
LED lights go red and another bar is illuminated.
- When the second to last LED flashes, this in-
dicates that the «reserve charge» is now being
used (70% of electricity used).
- When the last two LEDs flash alternately, this in-
dicates that the battery has some voltage (80%
of electricity used), but needs charging.
A170149 (EPT20-15ET)
The LEDs (1) represent battery residual capacity. The LCD (2) displays the operating hours.
The LED (3) is a fault alarm lamp.
Battery discharge indicator (1)
When the truck has been switched on via the key switch, the battery charge status is dis-
played. The LED colours (1) represent the following conditions:
Component
LED Colour
Green
Standard battery
Orange
residual capacity
Flashing red
Battery discharge at 70%, a flashing red light gives a warning, indicating that the stored
battery charge is low. Battery discharge at 80%:
Two flashing red lights give a warning, indicating that the battery is empty. Lifting is now
inhibited. The battery must be charged.
Operating hours display (2)
Display range between 0.0 and 99,999.0 hours. Travel and lifting are logged. This is a backlit
display.
5
Driving wheel
6
Fork
7
Battery
8
Puller
9
Knob
5
Driving wheel
6
Fork
7
Battery
8
Puller
9
Knob
5
Value
70-100%
30-60%
0-20%
7
1.2.1. Control handle
A170148 (EPT20-15HJ)
Item
Control/Display
11
Key switch (optional)
12
Boatlike switch
13
"Forward" button
14
"Backward" button
Safety function which, when activated, forces the truck
15
Collision safety switch
to reverse until the switch returns to the neutral position.
16
«Horn» button
17
Battery discharge indicator
A170149 (EPT20-15ET)
Item
Control/Display
12
"Lower" button
13
"Lift" button
14
Travel switch
15
Warning signal button
Safety function which, when activated, forces the truck
16
Collision safety switch
to reverse until the switch returns to the neutral position.
Power-up test
On power-up the display indicates:
- The operating hours
- The charge status
The battery discharge indicator has a memory function. It stores the battery power level
after the power has been switched off. The next time the power is switched on, it will dis-
play the previously stored power level. If you want to reset the battery discharge indicator,
please turn the key to the on position after the battery has been fully charged.
Low voltage protection
This vehicle has a low-voltage protection function.
When the battery voltage is low, the vehicle will only be able to be driven at slow speeds.
This means that the battery now needs to be charged.
1.3. Identification points and data plates
A170148 (EPT20-15HJ)
Item
Description
1
Truck data plate
2
"No riding" warning
3
Direction decal on control handle
4
"Charge LED Mode" decal
5
"J FINE" decal
6
Knob decal
7
Puller decal
A170149 (EPT20-15ET)
Item
Description
1
Direction decal on control handle
2
Truck data plate
3
Warning decal
4
Key switch decal
5
Logo decal
Function
Switches the control current on and off.
Switches the control current on and off.
Travel forwards.
Travel backwards.
Triggers a warning signal.
Display battery residual capacity.
Function
Lowers load forks.
Raises load forks.
Controls the driving speed and direction.
Triggers a warning signal.
6
8