Beissbarth SL 6 Serie Manual Original página 38

en 38 | SL 6xx |
Contents English
1. Symbols used
1.1 In the documentation
1.1.2 Symbols in this documentation
1.2 On the product
2. User information
2.1 Important notes
2.2 Safety instructions
2.3 Configuration
2.4 Other applicable documentation
3. Product description
3.1 Intended use
3.2 Measurement quantities
3.3 Measurement visualization (operation)
3.3.1 General information
3.3.2 Check of calibration and configuration 37
3.3.3 Main window
3.3.4 Switching between the two halves of
the window
3.3.5 Selection and actuation of control ele-
ment
3.3.6 Main menu
3.3.7 Tester selection zone
4. Operation
4.1 Switching the SL 6xx on and off
4.2 Starting software modules
4.3 Software module termination
4.4 Operating modes
4.5 Brake test sequence
4.6 Notes on operation
4.6.1 General information
4.6.2 Notes on brake testing
4.6.3 Notes on brake testing for four-wheel
drive vehicles
4.6.4 Notes on motorcycle brake testing
4.6.5 Notes on suspension tester
4.6.6 Notes on noise simulator
4.6.7 Notes on side slip tester
4.7 Selecting test routine
5. Manual mode (normal operation)
5.1 Mode activation and deactivation
5.2 Test sequences vehicles
5.2.1 Brake dynamometer BD 6xx / BD 7xx 43
5.2.2 Motorcycle test routine
5.2.3 Suspension tester SA / SN 6xx
5.2.4 Noise simulator SN 680
5.2.5 Side slip tester ST 600
|
1 691 706 020 2012-12-11
5.3 Remote control options
5.3.1 Manual entry of weights
36 5.3.2 Storing measured values
36 5.3.3 Display repetition
36 5.3.4 Deleting stored values
36 5.3.5 Displaying total deceleration
5.3.6 Display switching
36 5.3.7 Print-out of measurement results
36
36 6. Automatic mode
36 6.1 Mode activation and deactivation
36 6.2 Test sequences
6.2.1 Brake dynamometer BD 6xx / BD 7xx 55
37 6.2.2 Suspension tester SA / SN 6xx
37 6.2.3 Side slip tester ST 600
37
37 7. Super automatic mode
37 7.1 Mode activation and deactivation
7.2 Test sequence
37 7.3 Brake test options
7.3.1 Repetition of sub-task (Clear Last)
38 7.3.2 Parking brake on front axle
38 8. All-wheel super automatic mode
38 8.1 Mode activation and deactivation
38 8.2 Test sequence
39 9. Fault procedure
39 9.1 General information
39 9.2 Acknowledgement of warnings
39 9.3 BNet Office and SL 6xx
39 9.4 Brake dynamometer series BD 6xx
40 9.4.1 Warnings
40 9.4.2 Faults
40 9.5 Side slip tester ST 600
40 9.5.1 Warnings
9.5.2 Faults
41 9.6 Chassis tester SA / SN 6xx
41 9.6.1 Warnings
41 9.6.2 Faults
41
41 10. Appendix
41 10.1 Setting the date and time
10.2 Calculation methods
43 10.2.1 Deceleration
43 10.2.2 Out-of-roundness
43 10.2.3 Road surface adhesion
45
48
i
50 These operating instructions describe standard test
51 procedures. These standard test procedures may
differ from country-specific test procedures
52
52
53
53
53
54
54
54
55
55
55
58
59
60
60
60
61
61
61
62
62
62
63
63
63
64
65
65
65
65
65
65
65
65
65
66
66
67
67
67
67
Beissbarth GmbH