Tabla de contenido
remove
cover
belt
1.
Remove the two (2) screws (A) securing belt cover (B) to frame (C).
2.
Remove belt cover.
•
Replace belt cover by installing cover and screws and tighten se-
curely.
(_
Enffernen
der
riemenabdeckung
1.
Enffernen Sie die zwei (2) Schrauben (A), mit denen die Riemena-
beckung (B) am Rahmen (C) befestigt ist.
2.
Enffernen Sie die Riemenabdeckung.
•
Befestigen Sie die Riemenabdeckung erneut, indem Sie die Abdeck-
ung und die Schrauben wieder anbringen und die Schrauben fast
anziehen.
(_Pour
enlever
le
de
courroie
couvercle
la
1.
Enlevez les deux (2) vis (A) en fixant le couvercle de la
courroie (B) au ch#=ssis(C).
2.
Enlevez le couvercle de la courroie.
•
Remplaosz le couvemle de la courroie en installant le
couvercle et serrez solidement.
Desmontar el cubre correas
t.
Desmontar los dos (2) tornillos (A) qua sujetan el cubre
correas (B) a la carcasa (C).
2.
Desmontar el cubre correas.
•
Sustituir el cobra correas colocandola cubierta y los
tornillos y apretandofirmemente.
_N_ Her verwijderen
van de riemhuls
1.
Verwijder de twee (2) echroeven (A) die de riemhuls (B)
aan bet frame (C) bevestigen.
2.
Verwijder de riemhuls.
•
Zet de riemhuls wear terug door de huls en de schroeven
terug te plaatsen en draai stevig aan.
Rimuovere
il coperchio
della
cinghia
1.
Togliere Is due (2) viti (A) che fissano il coperchio della
cinghia (B) all'intelaiatura (C).
2.
Togliem il coperchio della cinghia.
•
Rimettem coperchio e vilt, stringendo bene.
replace belts
The auger and traction drive belts are not adjustable. If the belts are dam-
aged or begin to slip from wear, they should be replaced. It is recommended
that the belt(s) be replaced by a qualified service center.
NOTE: It is recommended
that both the auger and traction drive belt be
replaced at the same time.
The V-belts on your snow thrower are of special construction and should
be replaced by original equipment manufacturer (OEM) belts available
from your nearest dealer. Usingother than OEM belts can cause pemonal
injury or damage to the snow thrower.
WARNING:
Belt replacement
requires
separation
of the snow
_ thrower. While separating the auger housing (1) from the frame
assembly (2), It is important that an assistant stand In the oper-
ating position and hold the snow thrower handles (3). Serious
personal injury and/or damage to the unit could occur if the snow
thrower should fall during the belt changing process.
1.
REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel
tank into a suitable container, outdoors, away from fire or flame. Wipe
up any spilled gasoline.
2.
REMOVE DISCHARGE CHUTE- Loosen lock nut securing chute rota-
tor head to mounting bracket only enough to allow chute rotator head
to be raised and discharge chute to be removed from snow thrower.
3.
REMOVE BELT COVER - See "TO REMOVE BELT COVER" in this
section of this manual.
4.
REMOVE ENGINE PULLEY (A) - Remove bolt (B), lock washer (C)
and flat washer (D) securing pulley to engine crankshaft. Remove
outside (auger) pulley (A) only from crankshaft.
5.
SEPARATE SNOW THROWER - With your assistant standing in the
operating position holding the handles, remove the two bolts(F) and
lock washers (G) holding auger housing (1) and frame (2) together.
WARNING: As the last bolt is removed, have your assistant care-
fully lower the handles down to the ground.
6.
REMOVE AUGER BELT (H) from around pulley (E).
7.
RELIEVE TENSION
ON TRACTION
DRIVE BELT IDLER (J) and
remove traction drive belt (K) from around pulleys.
HINT: Insert a 3/8" drive ratchet (in the =ON" position) into the square hole
in idler arm (J) and rotate ratchet clockwise to relieve tension.
48
Tabla de contenido
