Idiomas disponibles
Idiomas disponibles
ted firmly in place and adheres correctly to the
vehicle seat; check that the seat belt is tight. If
the child car seat is not tightly and safely fitted
into the car seat, repeat the installation.
WARNING! In case of use in vehicles equipped
with rear seat belts with integrated airbags (in-
flatable belts), the interaction of the inflatable
portion of the vehicle's belt with this child re-
straint can result in serious injury or death! Do
not install this child restraint using an inflatable
seat belt. Install using ISOFIX instead, or move
the car seat to a position with a suitable seat
belt type. When installing with ISOFIX, the unu-
sed seat belt should not be buckled behind the
Child Restraint System as this will engage the
inflatable portion of the belt.
When seating your child refer to paragraph 13.
SEATING THE CHILD IN THE CHILD CAR SEAT
7. HOW TO FIT THE GROUP 2 (15-25 kg)
CHILD CAR SEAT TO THE CAR WITH A
3-POINT SEAT BELT and TOP TETHER
WARNING! Before fitting the child car seat
and seating your child, adjust the position of
the child car seat buckle (from A to B) as indi-
cated in paragraph 11. ADJUSTING THE CHILD
CAR SEAT BUCKLE.
Position the child car seat on the selected seat.
WARNING! Make sure there are no objects be-
tween the child car seat and the vehicle seat or
between the child car seat and car door.
Pull the car seat belt, and slide it through the
space between the backrest and the base of
the child car seat (Fig. 29).
Pass the abdominal part of the car's 3-point
seat belt through the specific red abdominal
belt guides (M). Pull it out from the other side
of the child car seat and fasten it to the buckle
of the seat until you hear a "CLICK" (Fig. 30).
Continue to assemble on the side of the retract-
able part of the belt. Completely insert the belt
in the red clamp (L), holding it open (Fig. 31).
After completing the assembly it is necessary
to make the safety harness as tight as possible.
Pull the diagonal part hard towards the retrac-
tor and fasten with the red clamp (L) (Fig. 32).
The assembly of the child car seat is complet-
ed exclusively with the installation of the Top
Tether (T).
WARNING! Refer to your car's user manual to
identify where the Top Tether of the child car
sear is attached to the car. This fastening point
is denoted with a specific label (Fig. 20) and
can be found in the positions indicated by the
figures 21A – 21B – 21C – 21D.
WARNING! Check that the Top Tether fasten-
er used is the one that has been specially des-
ignated. Do not confuse it with a ring used for
hanging bags (Fig. 22).
WARNING! Pass the Top Tether between the
top of the car seat backrest and the headrest.
Never pass the Top Tether above the car head-
rest.
Extend the Top Tether belt by pressing adjust-
ment button (V).
Once you have identified the fastening point,
connect to the Top Tether hook (U).
Adjust the length of the Top Tether belt by
forcefully pulling the belt until it is tight. The
indicator on the belt goes green (W) when
the tether is suitably tight (Fig. 33). Roll up any
excess belt and tie up using the velcro.
WARNING! Check that the child car seat is fit-
ted firmly in place and adheres correctly to the
vehicle seat; check that the seat belt is tight. If
the child car seat is not tightly and safely fitted
into the car seat, repeat the installation.
WARNING! In case of use in vehicles equip-
ped with rear seat belts with integrated ai-
rbags (inflatable belts), the interaction of the
inflatable portion of the vehicle's belt with this
child restraint can result in serious injury or de-
ath! Do not install this child restraint using an
inflatable seat belt.
This type of installation is SEMI-UNIVERSAL. To
check the compatibility with your vehicle refer
to the vehicle list supplied with the product.
When seating your child refer to paragraph 13.
SEATING THE CHILD IN THE CHILD CAR SEAT.
8. HOW TO FIT THE GROUP 2 (15-25 kg)
33
