•
: If timer 2 is enabled (par. 331
t.2.run
is switched to RUN, otherwise is kept in STOP;
•
: If timer 2 is enabled (par. 331
t.2.s.e.
status of the timer switches from STOP to RUN e vice versa;
•
: If timer 2 is enabled (par. 331
t.2.sta.
timer is switched to RUN;
•
: If timer 2 is enabled (par. 331
t.2.end.
timer is switched to STOP;
•
: With digital input active, the access to setpoint configuration/modification is locked;
Lo.cfG.
•
: If on par. 56
reM.s.e.
is enabled, otherwise the setpoint is local. On par. 234
it is necessary to select the reference regulation loop.
8.7
Automatic / Manual regulation for % output control
This function allows to switch from automatic functioning to manual command of the output
percentage.
With par. 48
(for regulation loop 1) or par. 67
A.ma. 1 .
two modes.
1 First selection (
enab.
showed
autom.
SET
Press
to visualize
keys
c
and
d
the output percentage. To back to automatic, with the same procedure, select
on display 2: immediately led
2 Second selection (
• If there is a temporary power failure or after switch-off, the manual functioning as well as the
previous output percentage value will be maintained at restarting.
• If the sensor breaks during automatic functioning, the controller switches to manual mode while
maintaining the output percentage command unchanged as generated by the PID immediately
before breakage.
Ex: on an extruder the command in percentage of the resistance (load) is maintained also in case of
input sensor failure.
8.8
Heater Break Alarm on CT (current transformer - only
on ATR244-13ABC and 23xx-T)
This function allows to measure load current to manage an alarm during a malfunctioning with power
in short circuit, always open or partial break of the charge. To enable this function set
par. 287
and the value of the connected transfomer, on par. 288
ct F.
• Seletct on par. 289
Alarm intervention.
• Select on par. 290
• Select on par. 291
• Select on par. 292
• It is possible to associate an alarm, selecting
or par. 177
or par. 195
aL. 4 .F.
It is possible to visualize on display 2 the average current, selecting
Selecting 0 on par. 290
an Heater Break Alarm.
20 - ATR244 - User manual
tmr.2
it is selected
rem.s.
) allows to enable with
; it's now possible, during the process visualization, modify through the
manu.
MAN
switches off and functioning backs to automatic.
) enables the same functioning but with two important variants:
en.sto.
the regulation loop referred to the current measure and the Heater Break
H.b.a.r.
the Heater Break Alarm intervention threshold in Ampere.
H.b.a.t.
the intervention threshold in Ampere to control the overcurrent.
ocu.t.
the delay time in seconds for the Heater Break Alarm intervention.
H.b.a.d.
or par. 213
aL.5.F.
it is possible to visualize the current consumption without generating
H.b.A.t.
different from
disab.
different from
tmr.2
different from
tmr.2
different from
tmr.2
or
) , with digital input active the remote setpoint
enab.
en.ser.
d. i . 1 .r.
(for regulation loop 2) it is possible to select
A.ma.2.
FNC
the writing
on par. 123
H.b.a.
aL.6.F.
) , with digital input active, the timer
) , acting on the digital input, the
disab.
) , acting on the digital input, the
disab.
) , acting on the digital input, the
disab.
or 242
or 250
d. i .2.r.
on display 1, while on display 2 is
p.---
.
ct v.
on par. 141
aL. 1 .F.
aL.2.F.
on par. 278
AMPEr.
or 258
d. i .3.r.
d. i . 4 .r.
autom.
or
on
50 Hz
60 Hz
or par. 159
aL.3.F.
.
vi.d.2