non torna in START automaticamente: per questa operazione è richiesto l'intervento
dell'utente.
248 d. i .3.c.
Digital Input 3 Contact
Definisce il contatto a riposo dell' ingresso digitale 3.
Normalmente aperto (Default)
n.open
Normalmente chiuso
n.cLos.
249 d. i .3.P.
Digital Input 3 Process
Seleziona la grandezza correlata all'ingresso digitale 3.
Valore letto sull'ingresso AI1. (Default)
A.in.1
Valore letto sull'ingresso AI2.
A.in.2
Media aritmetica dei valori letti sugli ingressi AI1 e AI2 [(AI1+AI2)/2].
MEAn
Differenza dei valori letti sugli ingressi AI1 e AI2 (AI1-AI2).
diFF .
Modulo della differenza dei valori letti sugli ingressi AI1 e AI2 (|AI1-AI2|).
Ab.dif .
Somma dei valori letti sugli ingressi AI1 e AI2 (AI1+AI2).
SuM
250 d. i .3.r.
Digital Input 3 Reference Command
Definisce il comando di riferimento per le funzioni dell' ingresso digitale 3.
Comando 1 (Default)
cmd. 1
Comando 2
cmd. 2
Comando 1 e 2
cmd.1.2
251÷254
Reserved Parameters - Group O
Parametri riservati - Gruppo O.
GRUPPO P -
d. i . 4
255 d. i . 4 .f.
Digital Input 4 Function
Funzionamento ingresso digitale 4.
Disabilitato (Default)
diSab.
2 Setpoints Switch
2t. sw.
2 Setpoints Switch Impulsive
2t.sw.i.
3 Setpoints Switch Impulsive
3t.sw.i.
4 Setpoints Switch Impulsive
4t.sw.i.
Start / Stop
st./st.
Run
rUn
Lock conversion (stop all conversions and display values)
HoLd
Performing manual tune
tune
Automatic / Manual Impulse (if enabled on parameter 48 or 67)
au.ma.i.
Automatic / Manual Contact (if enabled on parameter 48 or 67)
au.ma.c.
Action Type. Cooling regulation if D.I. is active, otherwise heating reg.
act.tY.
Analogue Input 0. Set AI to zero
A.i. 0
Manual reset. Reset the outputs if selected as manual reset
M. reS.
Timer 1 run. The timer 1 count with activated D.I.
t.1.run
Timer 1 Start End. D.I. starts and stops the timer 1(impulsive)
t.1. s.E.
Timer 1 Start. D.I. starts the timer 1(impulsive)
t.1.Sta.
Timer 1 End. D.I. stops the timer 1(impulsive)
t.1.End
Timer 2 run. The timer 2 count with activated D.I.
t.2.run
Timer 2 Start End. D.I. starts and stops the timer 2(impulsive)
t.2. s.E.
Timer 2 Start. D.I. starts the timer 2(impulsive)
t.2.Sta.
Timer 2 End. D.I. stops the timer 2(impulsive)
t.2.End
Lock configuration and setpoints
Lo.cfG.
Simula il funzionamento del tasto up.
up .key
Simula il funzionamento del tasto down.
down.k.
Simula il funzionamento del tasto fnc.
fnc. k.
Simula il funzionamento del tasto set.
set. k.
138 - ATR244 - Manuale d'uso
- Ingresso digitale 4
(solo su ATR244-23XX-T)