Tabla de contenido
Idiomas disponibles
Idiomas disponibles
English
display
would
Immediately contact the MESTRA technical
service.
The motor reducer which drives the blades of
the stirrer is protected by an automatic
disconnecting
switch,
microprocessor's own programming software,
which
disconnects
overloads occur.
During the unit´s operation, it is perfectly normal
for the metal casing to reach temperatures close
to 50 ºC, a value understood to be correct, with
the operations limits foreseen by TALLERES
MESTRAITUA, S.L.
All the units are checked before leaving the
factory. During the rigorous final quality control
carried out in TALLERES MESTRAITUA, S.L.
several test are made using gel, in order to
better simulate the true use conditions of the
unit. For this reason, it is completely normal to
receive your GEL BAT-6 with some remains of
gel inside the container.
PRECAUTIONS
♦ Before carrying out any maintenance on
the unit, switch it off and unplug from the
power supply.
♦ Before connecting the unit make sure the
electric connection is at 230 V, 50/60 Hz with
an earth connection.
♦ Neither children nor unqualified personnel
are allowed to manipulate the unit.
♦ Do not open the upper lid when the unit is in
operation. Under circumstances must you
bridge the safety switch which protects the
opening of the lid.
♦ Avoid the level of gel rising above 3 cm over
the last blade (the closest to the upper edge
of the container).
♦ Place the unit upon a flat surface, correctly
levelled, far from any sources of vibration.
Avoid the possibility of it tipping over.
♦ Make sure the tap is turned off before
starting up the unit.
♦ Do not pour the gel at a temperature (ºC1),
because it may scald you. Wait until the
pouring temperatures reaches (ºC2).
♦ During operation avoid touching the lid. It
may have a high temperature. In the gel
pouring
manoeuvre,
protection.
♦ Be extremely careful during the slow start
ups (the word "LEnt" appears on display
(1)). Eventual spattering or spillage of gel
may occur.
♦ Never leave the gel in liquid state during a
delayed start up. It may solidify, preventing a
normal start up of the unit. Always insert the
14
show
"rot1"
or
"rot2".
and
by
the
motor
whenever
wear
gloves
gel in pieces when programming a delayed
start up.
REMINDER
In short, we give you a simple and easy to
the
assimilate manner to carry out the most
elementary manoeuvres which can be done on
your GEL BAT-6:
To switch on the GEL BAT-6:
Turn on the main switch (13).
♦
Brieflly press the key (8) ºC1. Light (11) on
♦
the control graph will blink intermittently.
Press key (8) º(C1) for a few seconds.
♦
Light (11) on the control graph will switch
on permanently.
To switch off the unit (after executing the
programme):
Press key (9) (ºC2) for a few seconds. The
♦
lights on the control graph will blink
intermittently.
Turn off the main switch (13).
♦
To switch on the GEL BAT-6 in delayed startup:
Turn on the main switch (13).
♦
The first possibility is to press key (7) until
♦
word "hPro" and alternatively the expected
time to reach (ºC1) appear. If it is the time
you wish to programme for the unit to
reach (ºC1), press the clock key (7) for
several seconds.
To
turn
programme):
Press key (9) (ºC2) for several seconds.
♦
The lights on the control graph will blink
intermittently.
Turn off the main switch (13).
♦
In order to switch the unit off at any time during
the programme:
Press the key which corresponds to the
♦
step being taken for a few seconds, until
all the lights are blinking.
Disconnect the GEL BAT, acting upon the
♦
main switch (13).
DISPLAY MESSAGES
The GEL BAT-6 is provided with a series of
for
words wich appear on the display, in order to
facilitate the handling of the unit. These
messages are as follows:
HorA
Indicates the nearest time when the
ºC1temperature can be reached.
HPro
Indicates the time programmed by the
user(memorized).
Fred
Indicates a breakdown in the electric
power supply (higher than 10).
off
the
unit
(after
executing
a
Tabla de contenido
