Electronic Programmer - Cardin Elettronica SL Serie Manual Del Usuario

MANUAL MANOEUVRE WITH THE MOTOR RELEASED
Manual release is to be carried out with the motor Stopped. To release the gate use
the manual release key supplied with the unit. The key should be kept in an easily
accessible place.
SCREW OPERATED MANUAL RELEASE
SL1524SB
To release the unit (ig. 8a)
1. Lower the lock protection "A" on the
release knob, insert the key "B" and
rotate it through 180 degrees clockwise.
The knob is now free and can be rotated.
2. Rotate the knob "C" clockwise until
reaches its travel limit. The geared motor
is now released and the gate can be
moved manually.
Attention! Do not force the knob to
exceed the travel limit.
To relock the unit (ig. 8a)
1. Rotate the knob "D" anticlockwise until
it blocks completely.
Attention! Do not force the knob to
exceed the travel limit.
2. Rotate the key anticlockwise and posi-
tion the lock protection.
The geared motor is now locked and the
gate may be used normally.
Once the system is running normally
store the key in a safe place.
2-POSITION MANUAL RELEASE
SL1524
To release the unit (ig. 8b)
1. Rotate the lock protection disk on the
release knob, insert the key and rotate
it half a turn anticlockwise. The knob is
now free and can be released.
2. Rotate the knob through 90° clockwise.
The gears are now released and the gate
can be moved manually.
To relock the unit (ig. 8b)
1. Rotate the handle anticlockwise and
move it back to the blocked position.
2. Rearm the gears:
- electrically by giving an opening or closing command;
- by slightly moving the gate
3. Rotate the key clockwise and relock the handle.
Once the system has been reset store the key in a safe place.
Attention! Never use the manual release mechanism while the gate is in
operation. If you release the gate and then give a movement command
the following symbol will appear on the display
9
A
8
A
180°
B
5 - 6 turns
C
5 - 6 turns
D
8
.
Access to the electronic card
Attention! Before opening the cover make
sure that the power has been switched off
at the mains.
To access the motor loosen the two
screws "A" positioned on either end of the
cover as indicated in igure 9.

ELECTRONIC PROGRAMMER

Electronic programmer for a dc motor with an incorporated radio receiver card, which
allows the memorisation of 300 user codes (see "remote control" page 20). The
"rolling code" type decoder uses 433.92 MHz series transmitters.
The motor rotation speed is electronically controlled, starting slowly and increasing
in speed; the speed is reduced as it nears the travel limit so as to enable a controlled
smooth stop.
a
Programming is carried out using one button and allows you to set the system, the
current sensor and the entire gate travel distance while the logic carries out position
control using an encoder.
The intervention of the anticrush/antidrag sensor during the closing and opening
stages causes a brief (10 cm) travel direction inversion then a block.
IMPORTANT REMARKS
• After having installed the device, and before powering up the program-
mer, release the gate (manual release mechanism) and move it manually,
checking that it moves smoothly and has no unusual points of resistance.
• The programmer can activate the motor automatically. This is indicated
by the warning lights pre-lashing for 10 seconds, and by the symbol
appearing on the display ("automatic repositioning" on page 19).
• The programmer is itted with an electrical input monitoring system,
which is used to block the motor in emergency conditions; however
this system is not active during the following stages:
- during the irst 5 second of an opening stage starting from completely
closed
- during the irst 2 seconds of all other movement stages
- when the battery undercharged
Do not therefore attempt to physically block the door during these
stages, otherwise you may risk blowing the motor circuit protection
fuse "F1".
• If you need to check the status of the fuse "F2", disconnect the power
supply to the programmer; reconnect it only after having re-inserted
the fuse.
• The presence of the electrical input monitoring system does not exclude
the need to install photoelectric cells or other safety devices which
are foreseen by the local standards and regulations in force.
• The geared motor unit has been assembled in the factory to be itted
b
to the left side of the gate. Read the paragraph "instructions for
positioning the unit".
• For the correct operation of the programmer the incorporated batteries
must be in good condition: the programmer will lose the position of
the gate in case of blackouts when the batteries are lat, the alarm
will sound and automatic repositioning will take place .
Check the good working order of the batteries every six months (see
page 21 "Battery check").
• Before connecting the appliance make sure that the voltage and
frequency rated on the data plate conform to those of the mains
supply.
• An all pole trip switch with at least 3 mm between the contacts must
be installed between the unit and the mains supply.
• Don't use cables with aluminium conductors; don't solder the ends
of cables which are to be inserted into the binding posts; use cables
marked T min 85°C and resistant to atmospheric agents.
• The terminal wires must be positioned in such a way that both the
wire and the insulating sheath are tightly fastened (a plastic jubilee
clip is suficient).
Mains power supply connection
• Connect the control and security device wires.
• Run the mains power supply through the cable clamp located on the bottom right
of the main circuit board and to the separate 3-way terminal board:
- connect the neutral to binding post N
- connect the earth to binding post
- connect the live to binding post L
15
N
L