Idiomas disponibles
Idiomas disponibles
Operating mode S2 (short-term operation)
The machine may only be operated at maximum power for a
brief time.
Information about the noise level measured in accordance
with applicable standards (EN ISO 3744:1995, ISO 8528-
10:1998):
Sound pressure L
= 71.6 dB
pA
Sound pressure L
= 91.6 dB
wA
Measurement uncertainty K
= 1.13 dB
pA
Wear hearing protection.
Excessive noise can result in a loss of hearing.
8. Unpacking
• Open the packaging and carefully remove the device.
• Remove the packaging material, as well as the packaging
and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport dam-
age. In the event of complaints the carrier must be in-
formed immediately. Later claims will not be recognised.
• If possible, keep the packaging until the expiry of the war-
ranty period.
• Familiarise yourself with the product by means of the oper-
ating manual before using for the first time.
• With accessories as well as wearing parts and replace-
ment parts use only original parts. Replacement parts can
be obtained from your dealer.
• When ordering please provide our article number as well
as type and year of manufacture for your product.
m DANGER!
The device and the packaging are not children's
toys!
Do not let children play with plastic bags, films or
small parts! There is a danger of choking or suf-
focating!
9. Before commissioning
Electrical safety
Prior to use, the power generator and its electrical equipment
(including lines and plug connectors) should be checked to
ensure that there are no defects.
Never connect the power generator to the mains (socket).
The power lines to the consumer must be kept as short as pos-
sible.
Earthing (Fig. 3)
m Attention! Electric shock!
- Do not use bare wires for earthing.
- Power generator must be safely earthed.
Earthing the housing is necessary to discharge static charging.
To do this, connect a cable on one side to the earth terminal
(12) of the power generator and on the other side to an exter-
nal mass rising pipe (e.g. rod earth).
m ATTENTION!
Check before operation
• Check all sides of the engine for oil or fuel leaks.
• Check the engine oil level.
• Check the fuel level – Fill with at least 2 litres of Super E10
petrol.
• Check the condition of the air filter.
• Check the condition of the fuel lines.
• Look for signs of damage.
• Check that all protective covers are in place and all screws
are tightened.
• Ensure that the device is sufficiently ventilated.
• Make sure that the spark plug connector is attached to the
spark plug (20).
• Disconnect any connected electrical devices from the pow-
er generator.
9.1 Top up oil (Fig. 7 + 8)
m Attention!
The power generator is delivered without engine
oil. Therefore, ensure that you add oil before
starting it up. Please use 15W40 oil.
Check the oil level regularly before commissioning. An oil
level that is too low can damage the engine.
1.
Place the power generator on a level, even surface.
2.
Remove the engine cover (3) by unscrewing the two
screws with a Phillips screwdriver (not included in the
scope of delivery).
3.
Unscrew the oil dipstick (16).
4.
Fill the tank with engine oil using a funnel (14). Note the
max. filling capacity of 350 ml. Carefully fill the oil up to
the lower edge of the filler neck.
5.
Wipe the oil dipstick (16) with a clean, lint-free cloth.
6.
Re-insert the oil dipstick (16) and check the oil level with-
out screwing the dipstick tight again.
7.
The oil level must be within the middle mark on the oil
dipstick.
8.
If the oil level is too low, add the recommended amount
of oil (max. 350 ml).
9.
Then screw the oil dipstick (16) in again.
10. Put the engine cover (3) on and fix in place by retighten-
ing the two screws.
9.2 Refill with fuel
m Attention!
The power generator is delivered without petrol.
It is therefore essential to fill with petrol before
commissioning. Use Super E10 petrol for this.
1.
Unscrew the tank cover (2) and fill a maximum of 4.1 l
Super E10 petrol into the tank container using the funnel
(14).
2.
Ensure that the tank is not overfilled (Observe the fill level
marking (23)!) and that no petrol is spilled. Use a fuel
filter insert (22). Clean up spilled petrol immediately and
wait until the fuel vapours have evaporated (wipe dry).
3.
Close the tank cover (2).
7
GB/IE/NI/CY/MT
