Idiomas disponibles
Idiomas disponibles
28) Due to high mechanical loads, only durable rubber hose
lines (according to IEC 60245-4) or equivalent equip-
ment should be used.
29) Observe the electrical safety regulations applicable to
the place where the inverter power generator is used.
30) Consider the requirements and precautionary measures
in case of re-supply of a system by inverter power gen-
erators depending on the protective measures of this sys-
tem and the applicable directives.
Electrical safety
1.
Prior to use, the generator and its electrical equipment
(including lines and plug connectors) should be checked
to ensure that there are no defects.
2.
The power generating unit must not be connected to an-
other power source such as the power supply of energy
supply companies. In special cases where a reserve
connection to existing electrical systems is provided, this
must only be carried out by a qualified electrician who
will take into account the differences between the oper-
ated equipment using the public mains and operation of
the power generating unit. According to this part of ISO
8528, the differences in the operating manual must be
specified.
3.
Protection against electric shocks depends on the circuit
breakers which are matched precisely to the power gen-
erating unit. If a circuit breaker must be replaced, this
should be done using a circuit breaker with the same rat-
ing and performance characteristics.
ATTENTION: Use only Super E10 petrol as fuel.
m Use of petrol
m Danger to life! Petrol is toxic and highly flam-
mable.
• Only store petrol in containers (canisters) designed and
tested for this purpose. The tank caps must always be prop-
erly screwed on and tightened. Defective caps must be re-
placed for safety reasons.
• Keep petrol away from sparks, open flames, permanent
flames, heat sources and other sources of ignition. Do not
smoke!
• Refuel outdoors only and do not smoke while refuelling.
• Before refuelling, switch off the combustion engine and let
it cool down.
• Petrol must be filled before starting the combustion engine.
While the combustion engine runs or if the machine is hot,
the tank plug must not be opened and petrol must not be
filled.
• Open the tank plug carefully and slowly. Wait for the pres-
sure to equalise and only then remove the tank cover com-
pletely.
• Use a suitable funnel or filler pipe for refuelling so that no
fuel can spill onto the combustion engine and housing or
lawn.
Do not overfill the fuel tank!
• To leave room for the fuel to expand, never fill the fuel tank
beyond the lower edge of the filling nozzle. Observe ad-
ditional information in the combustion engine user manual.
6
GB/IE/NI/CY/MT
• If petrol has overflowed, do not start the combustion engine
until the petrol-contaminated area has been cleaned. Avoid
starting the engine until the fuel vapours have evaporated
(wipe dry).
• Always wipe up spilled fuel immediately.
• If petrol has got on clothing, it must be changed.
• The tank cover must be properly screwed on and tightened
after each refuelling operation. The device must not be put
into operation without the original tank cover screwed on.
• For safety reasons, check fuel line, fuel tank, tank plug and
connections regularly for damage, ageing (brittleness),
tight fit and leaks and replace if necessary.
• Only empty the tank outdoors.
• Never use beverage bottles or similar to dispose of or store
operating materials, such as fuel. People, especially chil-
dren, could be tempted to drink from it.
• Never store the device with petrol in the tank inside a build-
ing. Any fuel vapours produced can come into contact with
naked flames or sparks and ignite.
• Do not place the device and fuel tank near heaters, radiant
heaters, welding machines or other sources of heat.
Risk of explosion!
If a defect is detected on the tank, the tank cover or on fuel-
carrying parts (fuel lines) during operation, the combustion
engine must be switched off immediately. Then consult a spe-
cialist dealer.
7. Technical data
Power generator ..................................................Digital inverter
Protection category .......................................................... IP23M
Continuous output P
(COP) (230 V) (S1) ......................1.6 kW
n
Max. power P
(230 V) (S2 5min) ..............................2.0 kW
max
Rated voltage U
........................................................2 x 230 V
n
Rated current I
........................................................7 A (230 V
n
Rated current I
...................................................2 x 2.1 A (USB)
n
Frequency F
.......................................................................50 Hz
n
Performance class ................................................................... G1
Active power factor φ ................................................................ 1
Quality class ..............................................................................A
Drive motor type ...........................................4-stroke 1 cylinder
Displacement .................................................................... 79 cm
Max. power (engine) ........................................2.2 kW / 3 HP
Fuel .................................................................... Super E10 petrol
Tank contents ........................................................................4.1 l
Engine oil type ................................................................ 15W40
Oil volume (approx.) ....................................................... 350 ml
Consumption at full load ............................................... 1.27 l/h
Weight ..............................................................................17.5 kg
Max. temperature. ............................................................. 40
Max. altitude (above mean sea level) ..........................1000 m
Spark plug .........................................................................A7RTC
Technical changes reserved!
Operating mode S1 (continuous operation)
The machine may be operated continuously with the specified
power.
~
)
~
air-cooled
3
C
°
