Idiomas disponibles
Idiomas disponibles
Marks and Symbols on the Instrument
Symbol
Description
This equipment meets the requirements of all
relevant European safety directives. The equipment
carries the CE mark.
This equipment meets the requirements of all
relevant UK Statutory Instruments. The equipment
carries the UKCA mark.
This symbol, on the equipment, indicates that the
user should read the user manual.
This symbol, on the equipment, indicates a warning
and that the user should refer to the user manual.
Ground (Earth)
On/Off
Battery
Druck is an active participant in the UK and EU
Waste Electrical and Electronic Equipment (WEEE)
take-back initiative (UK SI 2013/3113, EU directive
2012/19/EU).
The equipment that you bought has required the
extraction and use of natural resources for its
production. It may contain hazardous substances
that could impact health and the environment.
In order to avoid the dissemination of those
substances in our environment and to diminish the
pressure on the natural resources, we encourage
you to use the appropriate take-back systems.
Those systems will reuse or recycle most of the
materials of your end life equipment in a sound way.
The crossed-out wheeled bin symbol invites you to
use those systems.
If you need more information on the collection,
reuse, and recycling systems, please contact your
local or regional waste administration.
Please visit the link below for take-back instructions
and more information about this initiative.
https://druck.com/weee
1. To Start
1.1 Location of Items
Refer to Figure A1 and Figure A2.
Item
Description
1.
On or off button.
2.
Left-hand soft-key. Selects the function above
it on the display (Item 24). Example: Edit
3.
Moves back one menu level.
Leaves a menu option.
ESC
Cancels the changes to a value.
Copyright 2005 Baker Hughes Company.
2 | DPI880 Instruction Manual–English
Item
Description
4.
Increases or decreases a value.
Highlights a different item.
5.
Holds the data on the display. To continue,
press the HOLD button again.
HOLD
6.
Shows the Select Task menu (Item 25).
Selects or accepts an item or value.
MENU
OK
Selects [] or cancels [ ] a selection.
7.
Right-hand soft-key. Selects the function
above it on the display (Item 24). Example:
Settings
8.
Display. Refer to Figure A3.
9.
Communications port. Use to connect a
SENSOR/
Universal Measurement Module (UMM) or a
PC
RS 232 cable.
10.
Connectors to measure or supply the specified
values. Refer to "Operation".
COM
Common connector
3W, 4W
3-wire, 4-wire RTD input
11.
Connection point for some of the optional
accessories. Refer to the datasheet.
12.
Battery compartment. Refer to Figure B1.
13., 14., 15.
(Dual Function) Connectors to measure or
supply the specified values. Refer to
"Operation".
Volts input or switch
Vin,
24Vo
24V loop power supply
1.2 Items on the Display
Refer to Figure A3.
Item
Description
16.
Task indication for the switch test.
= switch closed.
= switch open.
UPM only. Task indication for the leak test.
There is a 250Ω series resistor in the mA
circuit.
Refer to: Table 2 & Table 3.
17.
The loop power supply is on.
Refer to: Table 2 & Table 3.
18.
The data on the display is on hold. To
continue, press the HOLD button again.
19.
Shows the battery level: 0 ... 100%.
20.
Identifies the type of data.
= Input
= Output
= IDOS input
Refer to: Table 2 & Table 3.
21. ... 22.
The settings applied to the input or output:
21.
The thermocouple type (K, J, T ...) - (Table 4
K
& Table 5).
CJ=...
The cold junction temperature (Table 1).
Pt...
The RTD type (Pt50, ...) - (Table 4 & Table 5).
RTD input connections: 2, 3, or 4 (Figure 7).
