Introduction; Device Description; Scope Of Delivery; Intended Use - Scheppach CSP41 Traducción De La Instrucción De Original

1. Introduction

MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
we hope your new tool brings you much enjoyment
and success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liabili-
ty for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
We recommend:
Read through the complete text in the operating in-
structions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities in
accordance with the recommendations. The operat-
ing instructions contain important information on how
to operate the machine safely, professionally and
economically, how to avoid danger, costly repairs, re-
duce downtimes and how to increase reliability and
service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in
your country. Keep the operating instructions pack-
age with the machine at all times and store it in a
plastic cover to protect it from dirt and moisture.
Read the instruction manual each time before op-
erating the machine and carefully follow its informa-
tion. The machine can only be operated by persons
who were instructed concerning the operation of the
machine and who are informed about the associat-
ed dangers. The minimum age requirement must be
complied with.
In addition to the safety notices contained in this op-
erating manual and the particular instructions for
your country, the generally recognised technical reg-
ulations for the operation of identical devices must
be complied with.
 www.scheppach.com  [email protected]  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  [email protected]  +(49)-08223-4002-99  +(49)-08223-4002-58

2. Device description

1. Chain
2. Bar
3. Tensioning wheel
4. Claw Stop
5. Front Hand Guard / Chain Brake Lever
6. Front Handle
7. Starter Handle
8. Screwdriver
9. Air Filter Cover
10. On/Off Switch
11. Throttle Lock
12. Oil Tank Cap
13. Fan housing
14. Fuel Tank Cap
15. Rear Handle
16. Bar Cover
17. Choke Knob
18. Sword fastening knob and lever
19. Throttle
20. Chain Catcher Protection
21. Mixing tank
22. Spark plug wrench
23. Fuel pump

3. Scope of delivery

• Chainsaw (1x)
• Chain (1x)
• Bar (1x)
• Bar Cover (1x)
Open the packaging and remove the device carefully.
Remove the packaging material as well as the pack-
aging and transport bracing (if available).
Check that the delivery is complete.
Check the device and accessory parts for transport
damage.
If possible, store the packaging until the warranty pe-
riod has expired.
m ATTENTION!
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!

4. Intended use

The chain is designed exclusively for sawing wood.
You may only fell trees if you have received the ap-
propriate training. The manufacturer cannot be held
liable for damage caused by improper or incorrect
usage.
The machine is to be used only for its prescribed pur-
pose. Any other use is deemed to be a case of mis-
use. The user / operator and not the manufacturer
will be liable for any damage or injuries of any kind
caused as a result of this.
Please note that our equipment has not been de-
37 І 164