Idiomas disponibles
Idiomas disponibles
QST62-230CT-T50
Notice
Many events in the operating environment may affect the
tightening process and shall require a validation of results. In
compliance with applicable standards and/or regulations, we
hereby require you to check the installed torque after any
event that can influence the tightening result. Examples of
such events include but are not limited to:
• initial installation of the tooling system
• change of part batch, bolt, screw batch, tool, software,
configuration or environment
• change of air- or electrical connections
• change in line ergonomics, process, quality procedures
or practices
• changing of operator
• any other change that influences the result of the tighten-
ing process
The check should:
• Ensure that the joint conditions have not changed due to
events of influence.
• Be done after initial installation, maintenance or repair
of the equipment.
• Occur at least once per shift or at another suitable fre-
quency.
Safety and operating instructions
Safety instructions
Warning / Important
• Make sure you are familiar with the operator's instruc-
tions before you use this tool.
• The tool together with any attachements or accessories,
must never be used for anything other than the designed
purpose.
• All locally legislated safety rules regarding installation,
operation and maintenance shall be respected at all
times.
• This product is only intended for industrial use and shall
only be operated indoor in dry rooms. This product must
not be used in explosive atmospheres.
• Keep hands, long hair and other objects away from the
rotating socket.
• Make sure that the tool is in good working order and that
the controller is correctly programmed before use to
avoid unexpected behaviour from the tool which may re-
sult in operator injury.
• The tool with its drive/controller box is designed to oper-
ate at any setting within its torque range at a primary
voltage of nominal 400V/ 50Hz alternatively 480V/
60Hz, 3 phase. Refer to the manual for Your POWER
MACS or Drive unit.
• Check function of the earth fault protector and ground
loop continuity on regular basis according instructions in
the drive/ controller ASL.
• Always keep the POWER MACS/drive unit locked.
© Atlas Copco Industrial Technique AB - 9836 3788 00
• Always make sure that the POWER MACS/ drive is
switched off before connecting/disconnecting the tool
cable.
• Always disconnect the tool from the POWER MACS/
drive unit before making any adjustments on or inside
the Tool.
• Refer installation and servicing to qualified personnel
only.
• For proper reference between product and instruction,
note the Tool serial numbers here:
General information
General information
All tools are protected from overheating the motor by a de-
vice which cuts the power if the temperature rises abnor-
mally. When the temperature goes down again, the overheat
protection device resets automatically.
Electrical protection is based on two systems. One is passive
and earths the entire equipment and the other system is using
a fuse.
Changing, interfering or tampering with the protective sys-
tems voids all warranty and obligation from Atlas Copco.
Trouble-shooting and re-start of the system may only be car-
ried out by an authorized person.
Also check the continuity of the ground loop from the tool
body to proper earth. This control is recommended to be car-
ried out at least once every month.
EC DECLARATION OF INCORPORATION
We Atlas Copco Industrial Technique AB, S-105 23
STOCKHOLM, SWEDEN declare that this product (with
name, type and serial number, see front page) fulfils the fol-
lowing essential requirements of Machinery Directive
2006/42/EC, and must not be put into service until the final
machinery, into which it is to be incorporated, has been de-
clared in conformity with that Directive.It is also in conform-
ity with the following Directive(s):
2006/42/EC (Annex I, clauses 1.1, 1.2 (excluding 1.2.4.3),
1.3, 1.4, 1.5, 1.6, 1.7, EN ISO 12100), 2004/108/EC,
2006/95/EC
Harmonised standards applied:
EN 61010-1, EN 61000-3-2:2006, EN 61000-3-3:2008, EN
61800-3:2004
Technical file available from:
Quality Manager, Atlas Copco Industrial Technique, Stock-
holm, Sweden
Stockholm, 1 July 2013
Tobias Hahn, Managing Director
Signature of issuer
Safety Information
3
