Transport And Storage; Product Description - salmson Rocsan EVO Serie Instalacion Y Puesta En Servicio

English
3.

Transport and storage

3.1. Delivery
On delivery, immediately check that the product is complete and
undamaged. If any parts are damaged or missing, the transport
company or the manufacturer must be notified on the day of de-
livery. Claims made after this date cannot be recognized. Damage
to parts must be noted on the delivery or freight documentation.
3.2. Transport
Only the appropriate and approved fastening devices, transpor-
tation and lifting gear may be used. These must have sufficient
load-bearing capacity to ensure that the product can be trans-
ported safety. If chains are used they must be secured against
slipping.
The personnel must be qualified for the tasks and must follow all
applicable national safety regulations during the work.
The product is delivered by the manufacturer or shipping agency
in suitable packaging. This normally precludes the possibility of
damage occurring during transport and storage. The packaging
should be stored in a safe place for reuse if the product is fre-
quently used at different locations.
3.3. Storage
Newly supplied products are prepared so that they can be stored
for at least 1 year. The product should be cleaned thoroughly
before it is put into temporary storage.
The following should be taken into consideration for storage:
• Place the product on a firm surface and secure it against
slipping and falling over. Wastewater submersible pumps
are stored vertically.
DAnGER from falling over!
never set down the product unsecured. If the
product falls over, injury can occur!
• Our products can be stored at temperatures down to
-15 °C. The store room must be dry. We recommend a
frost-protected room for storage with a temperature
between 5 °C and 25 °C.
• The product may not be stored in rooms where welding
work is conducted as the resulting gases and radiated heat
can damage the elastomer parts and coatings.
• Any suction or discharge ports should be closed tightly
before storage to prevent impurities.
• The current supply cables should be protected against
kinking, damage, and moisture.
ELECTRICAL hazard!
Damaged power supply cables can cause fatal inju-
ry! Defective cables must be replaced by a qualified
electrician immediately.
BEWARE of moisture!
Moisture penetrating the cable will damage both
the product and the cable. never immerse the
cable end in fluid and always protect it from mois-
ture.
• The product must be protected from direct sunlight, heat,
dust, and frost. Heat and frost can cause considerable
damage to rotors and coatings!
• The impellers must be turned at regular intervals. This pre-
vents the bearings from jamming and the film of lubricant
on the mechanical shaft seal is renewed.
BEWARE of sharp edges!
Sharp edges can form on impellers and hydraulic
ports. There is a risk of injuries! Wear the necessary
protective clothing, e.g, safety gloves.
• If the product has been stored for a long period of time
it should be cleaned of impurities such as dust and oil
deposits before start-up. Rotors should be checked
for smooth operation. The housing coatings should be
checked for damage.
Before start-up, the filling level in the oil separa-
tion chamber should be checked and topped up, if
necessary.
Damaged coatings should be repaired immediately.
Only a coating that is completely intact fulfills the
criteria for intended use.
If these rules are observed, your product can be stored for a
lengthy period. Please remember that elastomer parts and coat-
ings become brittle over time. If the product is to be stored for
longer than 6 months, we recommend checking these parts and
replacing them as necessary. Consult the manufacturer for details.
3.4. Returning the product
Products that are returned to the factory must be properly
packaged. This means that impurities have been removed from
the product and that it has been decontaminated if used with
fluids that are hazardous to health. The packaging must protect
the product from damage during transportation. If you have any
questions please contact the manufacturer.
4.

Product description

The product has been manufactured with great care and is subject
to constant quality controls. Trouble-free operation is guaranteed
if it is installed and maintained correctly.
4.1. Proper use and fields of application
The Salmson-Rocsan evo... submersible motor pumps are suitable
for intermittent and continuous operation, pumping the following
fluids:
• Sewage and waste water
• Waste water containing feces
• Municipal and industrial waste water
• Sludge up to a maximum of 8 % dry solids
(depending on the type)
when draining buildings and properties in accordance with (DIN)
EN 12050 (while observing country-specific forewords and
regulations such as DIN EN 12050-1) and when used in pits and
reservoirs.
The submersible motor pumps must not be used for pumping:
• Drinking water
40