Transport, Handling And Storage - salmson MULTI-VE 2G Instalacion E Instrucciones

ENGLISH
1 - GENERAL
1.1 Applications
Pumps aimed at pumping clear liquids in building, agriculture and
industry areas ...
Water supply, water tower, sprinkling, high pressure washing, fire pro-
tection, boiler supply (with mandatory by-pass kit) – lifting of conden-
sates – air conditioning – industrial networks and integration in all
modular systems.
1.2. Technical characteristics
• Maximum operating pressure :
- Pump casing – PN 25
- Pump casing – PN 16
- Pump casing-rapid hose
coupling for Victaulic bracket
- Maximum suction pressure
• Temperature range :
- Standard versions EPDM O'ring and mechanical
seal (KTW/WRAS approved versions *)
- Versions for aggressive water
(Viton O'ring and mechanical seal )
• Maximum suction head
• Ambient temperature (standard product): + 50° C maxi
• Ambient humidity
* (WRAS : according to British standard - KTW : according to German standard).
2. SAFETY
Read this instruction carefully before installing and starting up. Pay
special attention to the points concerning the safety of the equip-
ment as regards the intermediate or final user.
2.1 Symbols used in the instruction
Security instruction :
non respect can induce injury.
Electrical security :
non respect can induce injury.
Security instruction : non respect can induce mate-
CAUTION !
rial damages.

3. TRANSPORT, HANDLING AND STORAGE

When receiving the material, check that there has been no damage
during the transport. If any defect has been stated, take all necessa-
ry steps with the carrier within the allowed time.
If the delivered material is to be installed later on,
CAUTION !
store it in a dry place and protect it from impacts
and any outside influences (humidity, frost etc...).
Due to high position of centre of gravity and small ground surfa-
ce of this type of pumps, beware of unstability during handling to
avoid any falling down and take necessary means to avoid inju-
ries or damaging.
Handle the pump carefully so as not to alter the goemetry and the
alignment of the unit.
4. PRODUCTS AND ACCESSORIES
4.1 Description (see figures 1, 2 ,4 ,5 ,6 ,7 ,8 ,9) :
1 - Strainer-foot valve
2 - Pump suction valve
3 - Pump discharge valve
4 - Non-return valve
5 - Venting and filling plug
: 25 bar
: 16 bar
: 25 bar (only 2, 4, 8 m3/h)
: 10 bar
: - 15° to + 120°C
: - 15° to + 90°C
: according NPSH of pump
: < 90 % maxi
6 - Drain-priming plug
7 - Pipe supports or brackets
8 - Strainer
9 - Storage tank
10 - Town water supply
11 - Switch and section switch with fuses
12 - Lifting hook
13 - Foundation block
14 - Cock
15 - Pressure sensor
16 - Tank
17 - Insulation valve of the tank
18 - Display
19 - Adjustment button
BP - By-pass
HA : Maximum suction head
HC : Minimum inlet pressure
4.2 The pump
Multistage vertical pump not self-priming, with ports in line on the
same axis in bottom part.
Shaft sealing by standardized mechanical seal.
Hydraulic connection
Oval flanges on the PN 16 pump casing : pump supplied with oval
cast iron counterflanges for screw-on tube, rings and bolts.
Round flanges : pump delivered with rings and bolts without counter-
flanges (accessories as option).
Rapid hose coupling (only 2, 4, 8m3/h) for "Victaulic" bracket : pump
delivered without brackets (accessories as option).
4.3 The motor and its speed variator
Asynchronous motor with standardized flange and shaft end for ver-
tical operation fitted with its speed variator.
Motor-pump linked by a coupling with safety guards.
Protection index motor-variator
Insulation class
Operating voltages and frequencies :
FREQUENCY
Voltages
4.4 Accessories (as option)
• By-pass kit • insulating valves • bladder or galvanised tank • tank
for antihammer blow effect • weld-on (Steel) or screw-on (Stainless
Steel) counterflange - rapid hose coupling like "Victaulic" • non-return
valves (with nose or spring ring when operating in mode 2) • strainer-
foot valve • vibrationless sleeves • protection kit against dry-running
– sensor kit for pressure regulation (accuracy : ≤ 1% ; use between 30
% and 100 % of the reading range).
5. INSTALLATION
Two standard types :
• Figure 1 : pump in suction
• Figure 2 : pump under pressure on storage tank (item 9) or town
water supply (item 10).
5.1 Installation
Install the pump in a place easy to reach, protected against frost and
as close as possible from the drawing point.
For heavy pumps provide a point of attachment (lifting hook) in the
pump axis (item 12) to facilitate removal.
Install the pump on a concrete block (at least 10 cm high) (item 13)
18
: IP 55
: F
50Hz - 60Hz Tolerance
380 to 440V ± 6%