Idiomas disponibles
Idiomas disponibles
Pole-mounted pruner cutting data
Guide rail length
Cutting length
Guide rail type
AL10-39-507P / Kangxin
Saw chain pitch
Saw chain type
Drive link thickness
Oil tank volume
Maximum motor speed
with pole-mounted
pruner n
max
Subject to technical changes!
Noise
Information on noise level per ISO 22868; EN ISO
3744:1995:
Grass
Brush
trimmer
cutter
Sound pres-
97.6 dB 97.6 dB 96.3 dB
sure level L
pA
Uncertainty
3 dB
3 dB
K
pA
Sound pow-
113.9 dB 114 dB 109.9 dB 109.6 dB
er level L
WA
Uncertainty
3 dB
3 dB
K
WA
Wear hearing protection.
Excessive noise can result in a loss of hearing.
Vibration:
Vibration value in accordance with ISO 22867:
Grass trimmer: A
= front 5.83 m/s
hv
Brush cutter: A
= front 5.81 m/s
hv
Hedge trimmer: A
= front 5.83 m/s
hv
Pole-mounted pruner: A
= front 5.84 m/s
hv
m/s
2
Measurement uncertainty K
PA
Keep the noise level and vibration to a minimum!
• Only use faultless devices.
• Maintain and clean the device at regular intervals.
• Adapt your working methods to the device.
• Do not overload the device.
• Have the device checked if necessary.
• Switch the device off if it is not in use.
• Wear gloves.
Warning!
In case of extended working periods, the operating
personnel may suffer circulatory disturbances in their
hands (vibration white finger) due to vibrations.
300 mm
260 mm
3/8"
3/8.050-39 / Kangxin
1.27 mm
140 cm³
9300 rpm
Pole-
Hedge
mounted
trimmer
pruner
96.2 dB
3 dB
3 dB
3 dB
3 dB
rear 8.14 m/s
2
2
rear 8.16 m/s
2
2
rear 8.14 m/s
2
2
rear 8.16
2
= 1.5 m/s
2
www.scheppach.com
Raynaud's syndrome is a vascular disease that caus-
es the small blood vessels on the fingers and toes to
cramp in spasms. The affected areas are no longer
supplied with sufficient blood and therefore appear
extremely pale. The frequent use of vibrating devices
can cause nerve damage in people whose circulation
is impaired (e.g. smokers, diabetics).
If you notice unusual adverse effects, stop working
immediately and seek medical advice.
Observe the following information to reduce hazards:
• Keep your body and especially your hands warm in
cold weather.
• Take regular breaks and move your hands to pro-
mote circulation.
• Ensure as little vibration as possible at the device
via regular maintenance and stable parts on the
machine.
7. Before commissioning
• Open the packaging and carefully remove the de-
vice.
• Remove the packaging material, as well as the
packaging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, keep the packaging until the expiry of
the warranty period.
m DANGER
The device and the packaging are not children's
toys! Do not let children play with plastic bags,
films or small parts! There is a danger of choking
or suffocating!
Before each start-up, check the device for the follow-
ing:
• Leak-tightness of the fuel system.
• Faultless condition and completeness of the guards
and the cutting device.
• All screw connections are tight.
• Smooth running of all moving parts.
Fuel and oil
• Recommended fuels
- Use only a mixture of unleaded petrol and spe-
cial 2-stroke engine oil. Mix the fuel mixture as
per the fuel mixing table.
- Do not use E10 fuel.
Attention:
Do not use a fuel mixture that has been stored for
more than 90 days.
GB | 49
