Idiomas disponibles
Idiomas disponibles
Using the optional flexible extension
To use the optionai spray tip extension, follow the instructions
below.
1. Remove the spray tip.
Be sure to leave the
,
atomizer valve in place.
2. Screw the end of the
extension tube with the
plastic threads to the
sprayer.
3. Remove the plastic
protector from the
metal end of the
extension.
Be careful not to lose the auxiliary atomizer
head under the plastic protector.
4. Screw the spray tip onto the flex tube with the auxiliary
atomizer head in place.
Selecting the proper tip
Your sprayer comes with a variety of spray tips depending on
the model: a round t p, a w de ang e tip (op ional), and a stain
tip (optional).
Wide angle tip
The wide angle tip produces a wide pattern th;_:_ can be
adjusted horizontally or verticatly.
I WARNINGI
SKIN INJECTION HAZARD - Do not place any part of your body
in front of the spray tip. Spray pressure could cause skin
penetration, resulting in severe injury and possible amputation.
Leave the sprayer unplugged until it is time to spray.
To adjust:
1. Make sure the sprayer is unplugged.
2. Loosen the wide angle tip by turning the collar
counterclockwise
1/4 turn.
3. Turn the tip guard so that it is pointing down for a
horizontal pattern. Turn the tip guard so that it is pointing
to the side for a vertical pattern.
Horizontal Pattern
Vertical Pattern
4. Tighten the tip firmly by hand.
NOTE: Make sure to tighten all spray tips firmly
by
hand. If the spray tip is not tightened firmly
enough, the sprayer could leak or the tip could
be damaged.
Do not use a tool to tighten the
spray tip. If the tip is too tight, it may be
damaged.
CAUTION]
If material is leaking from the threads between the spray
tip and the locking
nut, turn off the sprayer immediately
or
the sprayer could be damaged.
@ 1997 Wagner Spray Tech - All rights reserved.
The sprayer will leak from behind the spray tip if the swirl valve
is not seated properly.
If you notice material leaking from this
area:
1. Unplug lhe sprayer
--Pump Housing
immediately.
Opening
,-Locking
2. Remove the soray, t p
CoiFar
by turning it
counterclockwise.
3. Remove the swirl valve
and see it it needs to
,,
SorayT O
be cleaned or replaced.
Also check the piston
SwirrValve
housing opening for
any dirt or other obstruction a_d clean if necessary.
4. Put the swirl valve back in place, making sure it can seat
properly without any obstruction.
5. Thread on the spray tip by turning it clockwise and tighten
it firmly by hand.
Use the wide angle tip for covering a large, flat surface.
It
works well with most latex paints and stains. The wide angle
tip is not recommended
for use with oiFbased paints.
Round tips
The round tip produces a round pattern.
Use a round tip if the
surface you are spraying is too smal_ for use with the wide
angle tip.
The round tip comes in 3 sizes avai]able at your local retailer.
Use the size that works best for the type of material you are
spraying. The color of the tip center indicates its size.
1. Brown (light materials) - .016 inch (0,4 mm) opening,
This works best for stains, sealers, lacquers and water
proofers.
1. Blue (medium materials) - .023 inch (0.6ram) opening.
This size works best for oil-based materials.
2. Pir_k (heavy materials) - .031 inch (O.8mm) opening. This
all-purpose size works best for most materials.
Stain tip
The stain tip is an option incIuded with some models
It has a
specially designed opening for use with thin materials such as
thin stains, sealers and waterproofers,
and can be adjusted to
reduce overspray.
If you did not receive a stain tip and will be
spraying one of these materials, the tip can be purchased at
your Iocai retailer.
The stain tip pattern is round with a fine spray. To adjust the
spray pattern size and coarseness, turn the tip slightly
counterclockwise
to narrow the pattern and make the spray
more coarse. Turn the tip slightly clockwise to widen the
pattern and make the spray more fine.
