Idiomas disponibles
Idiomas disponibles
With the name of the volume
to
be adjusted
selected,
tum the
,._.,
SELECT knob to adiust the level
• To increase tile bass or treble:
Turn
the control
clockwise
{Tile bass or treble
sound can
{Mainunit)
be increased to up to +I 2 dB in steps of 2 dB)
• To decrease
the bass or treble:
Turn
the
control counterclockwise
(The bass or
treble sound can be decreased to up to -12
dBin steps of 2 dB)
If you do not want
the bass and treble
to be
adjusted, turn on the tone defeat mode
_E_
m The signals do not pass through the
bass and treble adjustment
circuits.
providing higher quality sound
(Main unit}
[2]
Listening
over headphones
Plug the headphones'
plug into
the iack
@
Connect the headphones
to
/_
_
the PHONES jack
_
_1'
The pre-out output
(including
1
the
speaker
output)
is
automatically
turned
off
when
headphones
are
connected
NOTE:
_o.Es
To prevent hearing loss, do not raise the volume level
excessively
when using headphones
oo_ooo
o
o
ooo
_
ann
[5]
Checking the currently
playing program source, etc,
Front panel display
• Descriptions of the unit's operations
m
are also displayed on the front panel
display
In addition, the display can
be switched to check the unit's
operating status while playing a
{Remote
SOUrce by pressing
the STATUS
c°n_luI u nit_
button
2
Using the dimmer function
• Use this to change the brightness of
=_=
the display
%
The display brightness changes in
four steps (bright, medium,
dim and
off) by pressing the main unit's
{Remote
DIMMER button repeatedly
control u nit_
8REGHT
_MEDIUM
_
DIM
OFF
2
[3]
Turning the sound off temporarily
( muting}
Use this to turn off the audio output
_,
temporarily
Press the MUTING button
Cancelling MUTING mode
{Remote
Press the MUTING button again
control u nt)
Muting
will
also be cancelled
when
MASTER
VOL is adjusted
up or down
[4]
Combining the currently
playing sound with the desired image
Simulcast playback
Use this switch
to monitor
a video
source other than the audio source
Press
the VIDEO
SELECT
button
repeatedly
until the desired
source
{Remote
appears on the display
control u r/t)
Cancelling simulcast playback
• Select
"SOURCE"
using the VIDEO SELECT
button
• Switch tile program
source to the component
connected
to the video input jacks
Set the external input (EXT IN) mode
Press the EXT IN button
_T.IN
tO_nputSWitch
the external
%
%
Once this is selected,
(Mainunit}
{Remote
the input signals
°°nt/°l unit}
connected
to the FL {front left), FR (front right),
C (center), SL {surround
left) and SR (surround
right) channels of the EXT IN jacks are output
directly to the front (left and right), center,
surround {left and right) speaker systems
without passing through the surround circuitry
In addition, the signal input to the SW (subwoofer)
jack is output to the PRE OUT SUBWOOFER jack
2
Cancelling the external input mode
To cancel
the external
input (EXT
IN) setting,
press the INPUT MODE (AUTO. PCM. DTS) or
ANALOG
button
to switch
to the desired
input
mode
(See page 16)
I_'_T UOaE
%%%%
{Man
unt)
{Remote
control
urn]t)
• When
the input mode
is set to the external
input
(EXT
IN),
the
play
mode
(DIRECT,STEREO,
DOLBY/DTS
SURROUND,
5CH STEREO
or DSP
SIMULATION)
cannot be selected
2
1
o._
Oo
......
_©_
NOTES:
• In play modes other than the external input mode,
the signals
connected
to EXT
IN jacks cannot
be played
In addition,
signals cannot be output
from channels not connected
to the input jacks
• The external input mode can be set for any input
source
To watch video while listening to sound.
select the input source to which tile video signal
is connected,
then set this mode
17
