The Functions Of The Breadmaker - Unold 68415 Instrucciones De Uso

Select the desired phase with the ABSCHNITT button.
Knead 1 and the programmed time 0:10 for this phase
appear on the display.
The time can be changed by means of the ZEITWAHL but-
ton. Press it repeatedly until the desired time appears on
the display (past OFF, if necessary).
Confirm the change with the ABSCHNITT button. Press
this button again and the next program phase and the pro-
grammed time will appear on the display: Rise 1 = and
0:20. If the maximum programmable time for the respec-
tive program phase is exceeded by pressing the ZEITWAHL
button, O will appear on the display if this is possible ac-
cording to the above table. This phase is then skipped

THE FUNCTIONS OF THE BREADMAKER

Alarm function
The alarm sounds:
ƒ whenever the MENU or ZEIT/time buttons are pressed,
ƒ when pressing the programme buttons to confirm
each step,
ƒ during the second kneading process, to remind you
to add seeds, fruit, nuts or other ingredients. Please
note that this function cannot be deactivated, e.g. in
the time preset function,
ƒ at the end of the baking process, the appliance beeps
often during the keep-warm phase,
ƒ at the end of the keep-warm phase several beeps
remind you that the appliance is now switched off
and the bread has to be taken out of the bread pan.
Please note that this function cannot be deactivated,
e.g. in the time preset function.
ƒ The alarm function cannot be inactivated.
Repeat function after power outage
Should the electricity supply been cut off during the op-
eration of the Breadmaker, the appliance will re-start, on
re-instatement of the supply, automatically from the point
arrived at when the cut-off occurred as long as the inter-
ruption is not longer than 2 minutes. If the interruption in
the electricity supply lasts more than 2 minutes and the
display shows the basic setting, the Breadmaker must be
re-started. This is only practical if the dough was not fur-
Stand 21.2.2020
Copyright UNOLD AG | www.unold.de
during the program. Every programmed setting must be
confirmed by pressing the ABSCHNITT button, so you can
continue programming the next program phase.
Once you have programmed all phases to suit your pref-
erences, conclude the programming by pressing the AB-
SCHNITT button and then the START/STOPP button. The
programmed time for the user program appears on the dis-
play. The program then starts either immediately or after
the time set via the timer function.
CAUTION:
The appliance becomes very hot
during operation
ther than the kneading phase when the break occurred. If
the program was already in the last rising cycle when the
power broke down and the interruption lasts over a longer
time, the dough cannot be saved and the program has to
be started again.
Safety functions
The lid should not be opened after the program has start-
ed, except during the second kneading phase for adding
of ingredients. During the rising and baking phase the lid
should never be opened, as the bread may sink down.
If the temperature in the appliance, due to previous use, is
too high (above 40 °C) for a newly chosen program, when
an attempt to re-start is made, the display will show H:HH
and an alarm sound will be heard. Should this occur, re-
move the pan and wait until the appliance has cooled off
and is back to the beginning of the originally chosen pro-
gram.
Please not that the breadmaker has no top heating for safe-
ty reasons, so the crust will be lighter on top and darker at
the sides and bottom of the bread. For safety reasons an
additional top heating is not allowed.
If after pressing START/STOPP, E:EE is shown in the dis-
play, the temperature control is defective. In this case
please send the appliance to our technical service.
DE
EN
FR
NL
IT
ES
PL
CZ
41 von 196