15 Troubleshooting - john deer R40EL Manual Del Operador

Pos: 13. 2 /In nent eil/Stör ungs urs ache n un d d ere n Beseiti gung /1 ST ÖRUNGSURSACHEN UND DEREN BESEITIGUNG @ 0 \mo d_1 115 373 523 343_ 152 1.d oc @ 1 904

15 TROUBLESHOOTING

Po s: 13. 3.1 / Inne nteil/St öru ngsu rsach en und der en Bes eitigu ng/Stö run gsta bellen elem ente /1 Tab ellenko pf @ 0\m od_ 111 537 476 0156 _15 21. doc @ 188 4
Fault
Po s: 13. 3.2 / Inne nteil/St öru ngsu rsach en und der en Bes eitigu ng/Stö run gsta bellen elem ente /Mo tor l äuft nicht an Elekt ro @ 0\ mod _11 2590 349 235 5_1 521. doc @ 18 90
Motor will not start
Po s: 13. 3.3 / Inne nteil/St öru ngsu rsach en und der en Bes eitigu ng/Stö run gsta bellen elem ente /Stark e Ersch ütte run gen (Vibri ere n) @ 0\m od_ 111 537 731 823 4_15 21. doc @ 190 0
Extreme vibration
Po s: 13. 3.4 / Inne nteil/St öru ngsu rsach en und der en Bes eitigu ng/Stö run gsta bellen elem ente /Schnitt uns aube r, R asen wi rd g elb, Elek tro @ 0\ mod _11 259 041 448 42_ 1521 .doc @ 18 99
Unclean cut, lawn is yellow
Po s: 13. 3.5 / Inne nteil/St öru ngsu rsach en und der en Bes eitigu ng/Stö run gsta bellen elem ente /Auswu rf ve rstop ft, Elekt ro @ 3\ mod _115 771 364 405 0_1 521. doc @ 19 339
Ejection blocked
GB
Pos: 13. 4 /In nent eil/Stör ungs urs ache n un d d ere n Beseiti gung /Stör ungs ursac hen un d de ren B eseitig ung Text Elektr o @ 0 \mo d_1 125 668 481 258_ 152 1.d oc @ 1 906
Repairs to electrical machines must always be performed only by qualified electricians. Please do not repair them yourself.
In the case of faults and defects which have not been listed here, please contact the nearest authorized dealer. This applies
in particular to appliances with electrical motors, as when these are repaired they must always undergo an insulation
protection test.
Your authorized dealer will also help you if you do not wish to perform any of the maintenance work described here yourself.
=== = = E nde der Stückliste == == =
Possible cause
No power supply voltage.
Connecting cable damaged.
Cutting height too low for grass that
is too high (high grass hampers the
starting of the motor).
Too much grass in housing.
Blade blunt.
Cutting height too low.
Mowing too fast.
Insufficient overlapping of cuts when
mowing.
Lawn becomes matted.
Cutting height too low for grass that
is too high.
Pushing mower too fast.
Grass not dry.
12
Remedy
Insert the power supply plug C2 .
Have the cable checked by an authorized
specialist workshop.
Adjust to higher cutting height I .
Tilt the machine forwards when you start it
up.
Clean cutter area from grass, keep gap
between fan and housing clean.
Have it checked by an authorized dealer
Have it sharpened and balanced by an
authorized dealer Q .
Adjust to higher cutting height I .
Adjust mowing speed.
Tall grass conditions may dictate that more
overlapping of cuts is required.
A lawn scarifier can remedy the problem
considerably
Adjust to higher cutting height I .
Adjust mowing speed.
Let grass dry.