Idiomas disponibles
Idiomas disponibles
Felling cut:
• Perform the felling cut from the other side of the trunk
while standing to the left of the tree trunk and sawing
with the saw chain pulling.
• The felling cut must run horizontal at least 5 cm above
the horizontal notch cut.
• It should be deep enough so that the distance to the
notch cut line is at least 1/10 of the trunk diameter.
• The part of the trunk that has not been sawn through
is called the bar (felling bar).
The bar prevents the tree from turning and falling in
the wrong direction.
Do not saw through the bar.
• As the felling cut approaches the bar, the tree should
begin to fall.
• If it appears that the tree is potentially not falling in the
desired direction or is leaning back and the saw chain
is jammed, stop the felling cut and use wooden, plas-
tic or aluminium wedges to open the cut and move the
tree to the desired fall line.
• If the trunk diameter is greater than the length of the
guide bar, make two cuts.
• After performing the felling cut, the tree falls by itself
or with the help of the felling wedge or crowbar.
DANGER
As soon as the tree begins to fall, remove the product
from the cut, stop the engine, place the product down
and leave the workplace via the escape route.
Watch out for falling branches and do not trip.
10.3.6
Release a jammed chainsaw
If the chainsaw becomes jammed during cutting, proceed
as follows:
1. Switch off the chainsaw and secure it on the inside of
the tree trunk (i.e. towards the tree trunk) or attach it
to a separate tool rope.
2. Pull the chainsaw out of the notch while lifting the
branch as far as necessary.
3. If necessary, use a handsaw or second chainsaw to
loosen the jammed chainsaw by cutting at least 30 cm
away from the jammed chainsaw.
Regardless of whether a hand saw or a chainsaw is used
to release a trapped chainsaw, the cuts to release the
chainsaw should always be made on the outside (towards
the tips of the branches) so that the chainsaw does not
get carried away with the sawn-off parts and further com-
plicate the situation.
10.4
After use
• Always switch the product off before placing it
down and wait until the product has come to a
standstill.
• Remove the battery.
• Place the guide bar and chain guard on the guide bar.
• Activate the chain brake.
• Allow the product to cool.
34 | GB
11 Cleaning
WARNING
Have maintenance and repair tasks that are
not described in this operating manual, car-
ried out by a specialist workshop. Use only
original spare parts.
There is a risk of accident! Always perform
maintenance and cleaning work with the bat-
tery removed. There is a danger of injury! Let
the Product cool down before all mainte-
nance and cleaning tasks. Elements of the
engine are hot. There is a danger of injury
and burning!
The product can start unexpectedly and cause injuries.
–
Remove the battery.
–
Allow the product to cool down.
–
Remove the tool attachment.
WARNING
Danger of injury when handling the saw
chain or the blade!
–
Wear cut-resistant gloves.
1. We recommend that you clean the product directly af-
ter every use.
2. Use a brush or hand brush to clean the saw chain and
no liquids.
3. Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasp-
ing surfaces do not allow for safe handling and control
of the tool in unexpected situations.
4. If necessary, clean the handles with a damp cloth
washed in soapy water.
5. Keep protective devices, air vents and the motor
housing as free of dust and dirt as possible. Rub the
product clean with a clean cloth or blow it off with
compressed air at low pressure. We recommend that
you clean the product directly after every use.
6. Ventilation openings must always be free.
7. Do not use any cleaning products or solvents; they
could attack the plastic parts of the product. Make
sure that no water can penetrate the product interior.
8. Clean the groove of the guide bar using a brush or
compressed air.
9. Clean the chain wheel and the spring tensioner.
12 Maintenance
Note:
Maintain the product carefully. Check for misalignment or
binding of moving parts, breakage of parts and any other
condition that may affect the product's operation. Have
damaged parts repaired before using the product.
www.scheppach.com
