Assembly; Area Of Application; Settings; Working Instructions - Parkside PKS 1500 A1 Instrucciones De Servicio

m Assembly
WARNING! For you own safety, only insert the mains
plug in an outlet when all assembly steps have been
completed and you have read and understood the
safety and operating instructions.
Lift the saw out of the packaging and place it on your
work bench. (Positioning of the saw on the work bench
- see the next page under „POSITIONING / WORK STA-
TION")
Installation of the dust bag
• Squeeze together the metal ring on the dust bag (12)
and attach it to the outlet opening in the motor area.
Assembling the work piece clamping device (fig. 1.1)
• Loosen the locking screw (17) and attach the work
piece clamping device (10) to the left or right of the
fixed saw bench.
• Afterwards, retighten the locking screws (17).
Assembling the work piece supports (fig. 1.1 – 1.2)
• Loosen the cross-head screw (14) and guide the work
piece support through the specified hole on the side of
the fixed saw bench.
• Make sure that the work piece support (15) is also
guided through the two plates (19) on the underneath.
• Afterwards, retighten the cross-head screw (14).
• Repeat this process on the other side.
Assembling the support stand (fig. 1.1 – 1.2)
• Loosen the cross-head screws (18) on the underneath
of the saw and guide the support stand (16) through
the specified holes on the back of the saw.
• Afterwards, retighten the cross-head screws (18).
m Area of application
Intended application possibilities
The machine cuts:
• Wood and materials similar to wood
• Plastic
Unintended application possibilities
The machine is not suitable for:
• Ferritic materials, steel and cast iron, as well as other
material types which are not listed, particularly food.
• Mitre saw without guard.
• Materials larger than the specified cutting data:
90°/90°/
90°/45°
45°/90°
45°/45°

Settings

CROSS-CUTTING
ATTENTION: Before carrying out the following adjust-
ments, please check whether the motor of the machine
is switched off.
120 x 60 mm
80 x 60 mm
120 x 35 mm
80 x 35 mm
Pivoting the table plate (Fig. 2)
The mitre saw can be pivoted left and right with the rota-
ry table. Exact angle adjustment is possible on the basis
of the scale. The angle can be precisely and quickly ad-
justed from 0° to 45° with locking positions at 15°, 22.5°
and 30°.
To pivot the rotary table, loosen the set screw (21) and
rotate the unit using the handle (20) until the desired
angle is reached. Then secure it with the set screw (21).
Tilt of the saw unit (Fig. 3)
The saw unit can be tilted at an angle of up to 45°.
Loosen the handle (23) on the rear side of the machine
and tilt the unit to the desired angle position according to
the scale. The angle can be set on the basis of the scale
(24) using the pointer (25). Then the handle must be re-
tightened.

Working instructions

After you have carried out all the tasks described above,
you can begin working.
ATTENTION: Always keep your hands away from the
cutting zone and never attempt to reach in while cutting.
FIXING A WORKPIECE
Clamp the work piece on the work table with the workpi-
ece clamp (10 - Fig 1) in order to fix it in place.
Cross-cutting (Fig. 4, 1.3)
Attention! For 90° mitre cuts, the moveable stop rail
(27a) must be fixed in the inner position.
• Open the set screw (27b) on the moveable stop rail
(27a) with an Allen key and push the moveable stop
rail (27a) inwards.
• The moveable stop rail (27a) must be locked in a po-
sition far enough from the inner position that the dis-
tance between the stop rail (27a) and the saw blade
(5) is no more than 8 mm.
• Before making the cut, check that no collision could oc-
cur between the stop rail (27a) and the saw blade (5).
• Secure the locking lever (27b) again.
• Loosen the locking knob (26).
• Lift the saw unit by the handle (2) until it locks in place
in the top position.
• Lock the material with the clamping device (10) on the
fixed saw table to prevent the material from moving
during the cutting operation.
• Press the workpiece evenly on the stop strips (27);
make sure that you hand remains outside the cutting
area of the saw blade.
• With your right hand on the handle (2), press the locking
lever (3) so that the unit can also be pivoted downward.
• The motor starts when the start button (1) is pressed.
• Slowly bring the saw blade down to the workpiece and
cut through it with moderate pressure.
• When the cutting operation is completed, move
the machine head back to its upper (home) po-
sition and release the
Attention! The machine executes an upward stroke
automatically due to the return spring, i.e. do not re-
ON/OFF button (1).
GB/IE 7