Idiomas disponibles
Idiomas disponibles
10.1.1 Cutting narrow workpieces (fig. 20)
Be sure to use a push stick (14) when making longitu-
dinal cuts in workpieces smaller than 120 mm in width.
A push stick (14) is supplied with the saw! Replace a
worn or damaged push stick immediately.
1.
Adjust the parallel stop (7) to the width of work-
piece you require (see 9.4).
2.
Feed in the workpiece with two hands. Always use
the push stick (14) in the area of the saw blade.
3.
Always push the workpiece through to the end of
the splitter (3).
m WARNING: With short workpieces, use the push
stick (14) from the beginning.
10.1.2 Cutting extremely narrow workpieces
(fig. 21)
Be sure to use a push block when making longitudinal
cuts in very narrow workpieces with a width of 30 mm
and less. There is no push block supplied with the saw!
(Available from your specialist dealer) Replace the
push block without delay when it becomes worn.
When sawing workpieces, these can become jammed
between the parallel stop and the saw blade, be caught
by the saw blade, and be thrown from the machine.
Therefore, the low guide face of the parallel stop is best
used in this case (see fig. 16).
If required, change over the stop rail (see 9.4.2).
1.
Adjust the parallel stop to the width of workpiece
you require.
2.
Use the push block to press the workpiece against
the stop rail and push the workpiece with the push
stick (14) through to the end of the splitter.
10.1.3 Making angular cuts (fig. 22)
Angular cuts must always be made using the parallel
stop (7).
The parallel stop (7) must always be fitted to the right
of the saw blade. Otherwise, workpieces can become
jammed between the parallel stop and the saw blade
during sawing and ejected at speed.
1.
Set the saw blade (5) to the desired angle (see
9.3).
2.
Set the parallel stop (7) in accordance with the
workpiece width and height (see 9.4).
3.
Carry out the cut in accordance with the workpiece
width (see 10.1).
10.2 Making transverse cuts (fig. 23)
1.
Push the transverse stop (2) into the groove (40)
of the saw table and set it to the required angle
(see 9.5).
2.
Use the stop rail (17).
3.
Press the workpiece firmly against the transverse
stop (2).
4.
Switch on the saw.
5.
Push the transverse stop (2) and the workpiece
toward the saw blade (5) in order to make the cut.
m WARNING: Always hold the guided part of the work-
piece. Never hold the part which is to be cut off.
6.
Push the transverse stop (2) forward until the
workpiece is cut all the way through.
7.
Switch off the saw again.
8.
Do not remove the offcut until the saw blade has
stopped rotating.
10.3 Cutting particle boards
To prevent the cutting edges from cracking when work-
ing with particle boards, you should not set the saw
blade (5) more than 5 mm greater than the thickness of
the workpiece (also see 9.2).
11. Transporting the equipment (fig. 24)
• Turn off the power tool before any transport and dis-
connect it from the power supply.
• Lower the saw blade (5) as far as possible.
• Wind up the mains cable (41).
• Carry the power tool with both hands by the fixed
saw table (1). Never use the table width extension to
carry the power tool.
• Protect the power tool from knocks, bumps and strong
vibrations, such as during transport in vehicles.
• Secure the power tool against overturning and slid-
ing.
• Never use the safety devices for handling or trans-
porting purposes.
12. Maintaining the equipment
m WARNING: Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
12.1 General maintenance measures
• Keep protective devices, air vents, suction openings
and the motor housing as free of dust and dirt as
possible. Remove shavings and dust with a vacu-
um cleaner and a brush. In addition, blow it out with
low-pressure compressed air.
www.scheppach.com
GB | 39
