Refitting Of The Front; Correct Positioning Of The Reversing Gear Ballast 3500 - 4500 - 6000-7500 - 9000 - 11000 - 13500 - battioni Pagani BALLAST 3500 Manual De Instrucciones De Uso Y Mantenimiento

user and maintenance
instruction manual BALLAST series

3.8.4 REFITTING OF THE FRONT

.../M-MA-K-KA
1) Remove the seeger
ring;
2) Remove the bearing;
3) Replace the flange
gasket;
4) Insert the pins
supplied in the
body;
5) Attach the gearbox to
the body with screws
tightened to
45 ÷ 55 Nm;
6) Using a buffer, install
the bearing onto
the flange, install
the compensation
ring and install the
seeger ring;
7) Install the spacer and
mount the pinion on
the shaft;
8) Fit the pinion fixing
self-locking nut;
9) Insert the gear in the
bearing seat;
10) Install the box cover;
11) Fill the gearbox with
oil;
12) Remove the
centring pins from
the body.
3.8.5 CORRECT POSITIONING OF THE REVERSING GEAR
BALLAST 3500 - 4500 - 6000 - 7500 - 9000 - 11000 - 13500
To position the reversing gear correctly, follow the procedure below:
1. remove the handle;
2. remove the manifold cover;
3. check that the flat part of the reversing gear
is placed at 45° with respect to the power take-off;
4. refit the manifold cover;
5. refit the handle.
p. 44
.../P
1) Remove the seeger
ring;
2) Remove the bearing;
3) Replace the seal on
the flange;
4) Insert the pins
supplied into the
body;
5) Install the front flange
onto the body using
screws tightened to
45 ÷ 55 Nm;
6) Using a buffer, install
the bearing onto
the flange, install
the compensation
ring and install the
seeger ring;
7) Refit the front cover
back onto the flange;
8) Remove the centring
pins from the body.
.../D
1) Remove the seeger 1) Remove the seeger
ring;
2) Remove the 2) Remove the
bearing;
3) Replace the seal on 3) Replace the seal on
the flange;
4) Insert the pins 4) Insert the pins
supplied into the
body;
5) Install the front 5) Install the front
flange onto the
body using screws
tightened to 45 ÷
55 Nm;
6) Using a buffer,
6) Using a buffer,
install the
bearing onto the
flange, install the
compensation
ring and install the
seeger ring;
7) Reassemble the
7) Refit the front cover
back onto the
flange;
8) Re-fit the hydraulic
8) Replace the splined
plug.
9) Remove the
9) Remove the
centring pins from
the body.
.../H
1) Remove the seeger ring;
ring; 2) Remove the bearing;
3) Replace the flange
bearing; gasket;
4) Insert the pins supplied
the flange; in the body;
5) Install the front flange
supplied into the
onto the body using
body;
screws tightened to 45 ÷
55 Nm;
flange onto the
body using screws 6) Using a buffer, install the
tightened to 45 ÷ bearing onto the flange,
55 Nm; install the compensation
ring and install the
seeger;
install the
bearing onto the
7) Install the spacer and
flange, install the
mount the pinion on the
compensation
shaft;
ring and install the
seeger ring; 8) Fit the pinion fixing self-
locking nut;
transmission sleeve
9) Insert the gear in the
on the rotary pin;
bearing seat;
10) Remove the centring
motor support;
pins from the body.
centring pins from
the body.
... / G-GA