Handling The Equipment - Scheppach HS110 Traduccion Del Manual De Instrucciones Originales

• Notes concerning the batteries:
- If you are not going to use the laser for a pro-
longed period, please remove the batteries from
the battery compartment. Otherwise, the leaking
of battery fluid might damage the device.
- Do not place the batteries on radiators or expose
them for a prolonged period to strong sunlight;
temperatures above 45 ° could damage the de-
vice.
2. Initial mounting of the laser module:
- Mount the laser using the two Phillips head
screws (z), Fig. 15.
3. Adjust the saw blade (4) to a max. cutting depth,
move to the 0° position and lock in place.
4. Dismantle the saw blade guard (2) (not during ini-
tial assembly).
5. Release the two attachment bolts (25) and remove
the table insert (5).
6. Loosen the fixing screw (26) (use the open-ended
spanner AF8 supplied).
7. Push the riving knife (3) upwards.
8. The distance between the saw blade (4) and riving
knife (3) should be between 3 mm and max. 5 mm,
(Figure. 18)
9. Retighten the attachment bolts (26) and mount the
table insert (5).
10. Mount the saw blade guard (2) with the screw and
knurled nut and flat washer (27).
9.6 Connecting an extraction device (Fig. 2)
1. Connect a suction hose to the suction adapter (16).
Secure the suction hose with a hose clamp if nec-
essary (not included in the scope of delivery), to
prevent it slipping off the suction adapter (16).
2. A household vacuum cleaner is not suitable for
use as an extraction device. Use a multi-purpose
suction device or an extraction system designed
specifically for sawdust.

10. Handling the equipment

10.1 On/off switch (fig. 3)
• It is possible to switch the saw on by pressing the
green "I" button. Before starting sawing, wait until
the saw blade has reached its maximum speed.
• In order to switch the saw off again, it is necessary to
press the red "0" button.
10.2 Setting the cutting depth (fig. 1+3)
The saw blade (4) can be adjusted to the required cut-
ting depth by turning the hand wheel (9).
42 | GB
• Counter-clockwise: Greater cutting depth
• Clockwise: Smaller cutting depth
Check the setting with a test cut.
10.3 Setting the angle (fig. 1, 17, 21, 22)
Angled cuts of 0°-45° to the left of the parallel stop (14)
can be carried out with the circular table saw.
m Before making every cut, check that no collision can
occur between the stop rail (30), transverse stop (31)
and the saw blade (4).
1. Loosen the locking handle (7).
2. Set the desired angle on the scale by turning the
hand wheel (9).
3. Lock the locking handle (7) at the desired angle
setting.
10.4 Using the parallel stop (fig. 17-23)
10.4.1 Setting the stop height (fig. 17+18)
• The stop rail (30) of the parallel stop (14) has two
guide surfaces at different heights.
• Depending on the thickness of the material to be
cut, the stop rail (30) must be used for thick material
(workpiece thickness exceeding 25 mm) and for thin
material (workpiece thickness below 25 mm).
10.4.2 Turning the stop rail (fig. 17)
1. To turn the stop rail (30), first loosen the knurled
nuts (i).
2. The stop rail (30) can now be pulled off the parallel
stop (14) and then slid over this again with the cor-
responding guide.
3. Tighten the knurled nuts (i) again.
4. The stop rail (30) can be attached to the left or right
of the parallel stop (14) as required. To do this, only
mount the screws from the other side of the paral-
lel stop (14).
10.4.3 Setting the cutting width (fig. 18+19)
The parallel stop (14) must be used when cutting sec-
tions of wood lengthways.
1. Place the parallel stop (14) from above on the
guide rail (15) for the parallel stop (14).
2. 2 scales are printed on the guide rail (15) for the
parallel stop (14), which show the distance be-
tween the parallel stop (14) and the saw blade (4).
3. Select the appropriate scale depending on wheth-
er the stop rail (30) has been turned for processing
thicker or thinner material:
High stop rail: thick material
Low stop rail: thin material
www.scheppach.com