Folder Navigation And Icons; Page Navigation; Accessing Parameters; Dashboard Icons - Ingersoll Rand R30 Información Del Producto

93014.15.06


Folder navigation and icons

To move among the tabbed folders shown on the LCD display, press the
RIGHT and LEFT keys. The navigation rolls over from the last to the fi rst folder
and vice-versa.
Folder
Icon
Name
Home
Operator
Settings
Events
Trip History
Graphing
Maintenance
General
Settings
Integral
Sequencing
Status
Factory
Settings


Page navigation

Once the desired folder is selected, press the DOWN key to move to the page
selection area and then use the RIGHT and LEFT keys to select the desired
page. Use the UP key to get back to the folder tabs.
Table 8 : Title Bar Page Icons
Icon
Start of the page selection area.
Indicates that there are more pages available by navigating
right.
Indicates that there are more pages available by navigating
left.


Accessing parameters

After the desired page is selected, the page's parameters can be selected by
using the DOWN key. The cursor will move to the next parameter each time
the DOWN key is pressed. Use the UP key to go back to the previous one.
The cursor rolls over, so once the last parameter is selected, pressing the
DOWN key will navigate the cursor to the folder bar. If the fi rst parameter is
selected, pressing the UP key will move the cursor to the page selection area.
Once selected, access parameters by pressing the ENTER key. Make changes
using the navigation keys and then enter the setting by pressing the ENTER
key again. After a parameter is accessed, pressing the ENTER key will enter
the current setting into the control program and navigate the cursor back to
the selected parameter on the page.
When the cursor is on a parameter that has an enabled/disabled box,
pressing the ENTER key will cause the setting to toggle.
This "X" icon appears on numeric entry windows as shown below. Placing the
cursor on it and then pressing the ENTER key will cancel the entry and any
changes that were made.
80447162 Rev B
Table 7 : Folder Bar Icons
Description
System performance and status main
information. The fi rst page of this folder is the
default page when the controller fi rst powers up.
System options and confi guration settings.
System events log.
Details on the most recent trips.
On-board graphing of system data. (Optional for
some controllers)
Status and notifi cation setup for compressor
maintenance items.
General settings such as Language, Time, and
Units of Measure.
Inter Module communication status and
confi guration.
Measurements or status from/of all analog and
digital I/O.
Compressor tuning parameters. Also displays
hardware and software versions.
Description
Figure 10 : Numeric Entry Window
Not all pages have adjustable parameters. Some just have read-only
information.


Dashboard icons

The dashboard is intended to be a quick at-a-glance view of system status.
The following table lists standard dashboard icons and their defi nition.
Note that the color of these icons changes based on the state set by the
application while running.
Table 9 : Dashboard Icons
Name Icon Description
Network
Network control is enabled.
Control
A service reminder is nearing or has expired
Service
Required
(i.e.: an air or oil fi lter needs to be changed).
Unloaded Compressor is in the unloaded state.
or
Loaded Compressor is in the loaded state.


Folder Options (Fixed Speed)



Home folder

Page 1: System Overview
Figure 11 : Home Folder
This is the factory default display after powering up the system.
• Online Pressure Setpoint is indicated in the white box and by the white
arrow, which is always left of center on the gauge.
• Offl ine Pressure Setpoint is indicated in the white box and by the white
arrow, which is always right of center on the gauge.
• Package Discharge Pressure is indicated by the large numbers centered
below the gauge and by the red arrow.
• Pressure Unit of Measure is indicated below the Package Discharge
Pressure. This is selectable from the General Settings folder.
• Airend Discharge Temperature is indicated by the numbers in the lower
left of the display.
• Temperature Unit of Measure is indicated to the right of the Airend
Discharge Temperature. This is selectable from the General Settings folder.
NOTICE
EN
EN-13