Memory Management Menu; Information And Diagnostic Menu - myone LUCE R Manual De Instalación Y Mantenimiento

TIN Allows importing the badges and the numerical codes used in another automation, already saved on a SD micro
TAG INPUT
memory. Choose from the following values:
NO = no import
YES = imports the badges and numerical codes on the SD micro memory
TOUT
Allows saving the badges and the numerical codes in the automation in use, on a SD micro memory. Choose
TAG OUTPUT
from the following values:
NO = no saving
YES = saves the badges and numerical codes of the automation on the SD micro memory
STCL
Setting the door closed and locked signal, in the presence of a bistable lock and micro-switch. Choose from the
CLOSED
following values:
DOOR SIGNAL
NO = the "door closed" symbol remains lighting even if the door is opened by hand.
YES = the "door closed" symbol only lights up when the door is really closed and locked.
N.B. if the lock does not close the door, the symbol "door closed" flashes.

11.4 MEMORY MANAGEMENT MENU

Using the buttons ↑ and ↓ choose the MEM menu, press ENTER to select and adjust the following memory management parameters.
Display Description
FSET Restores all the settings to factory values. Choose from the following values:
FACTORY
NO = no resetting.
SETTINGS
YES = resetting the factory settings.
FW
Electronic control programming procedure.
FIRMWARE
Insert the SD micro memory in the electronic control.
UPGRADE
From this menu, choose the desired firmware version.
Press the ENTER key until the programming procedure starts with a duration of approx. 30 seconds (or approx.
2 minutes for EMERGENCY automations), at the end of which the writing "SAVE" appears.
At the end of the procedure, remove the SD micro memory from the electronic control and keep it for future use.
N.B. In the event of a programming error or missing firmware (W100, W104), proceed as follows: disconnect
power, insert the SD micro memory, power, the programming procedure automatically starts or choose the
firmware from the menu present.
SIN Allows importing the settings of the menu used in another automation, already saved on the SD micro memory.
SETTING
Choose from the following values:
INPUT
NO = no import
YES = setting import on SD micro memory
SOUT Allows saving the automation in use menu settings, on a SD micro memory.
SETTING
Choose from the following values:
OUTPUT
NO = no saving
YES = saves setting of automation on SD micro memory

11.5 INFORMATION AND DIAGNOSTIC MENU

Using the buttons ↑ and ↓ choose the INFO menu, press ENTER to select and adjust the information and diagnostics parameters.
Display Description
SHOW
Displays info on operation and anomalies. Choose from the following values:
DISPLAY INFO
CONT = the display shows the contacts enabled of the terminal boards and alarms.
WARN = the display shows the alarms only.
VER Displays the firmware version of the electronic control (for example = 0200).
VERSION
CYCL Displays the number of manoeuvres made by the door (1 = 1,000 manoeuvres, 9000 = 9,000,000 manoeuvres).
CYCLES
SERV Enabling the routine maintenance signal of the door.
SERVICE
NO = no signal
SIGNAL
1 = 1,000 manoeuvre / 9000 = 9,000,000 manoeuvres
LOG Allows saving the following information in a SD micro memory (sliding_log.txt): the last 20 alarms, the settings of
INFO
the menu and the electronic devices connected to automation. Choose from the following values:
OUTPUT
NO = no saving
YES = saves information on automation on SD micro memory
WARN Displays the last 10 alarms (alarm number 0 is the last):
WARNING
0.xxx / 1.xxx / 2.xxx / 3.xxx / 4.xxx / 5.xxx / 6.xxx / 7.xxx / 8.xxx / 9.xxx
LIST
22
NO
NO
NO
Default settings
NO
- - - -
NO
NO
Default settings
COUNT
- - - -
0000
0000
NO
0.- - -