Tabla de contenido
Release Time (Controller number 72)
Status
2nd byte
BnH
48H
n = MIDI channel number:
vv = Release Time value (relative change): 00H - 7FH (-64 - 0 - +63),
* The Release Time parameter (EDIT:Tone Edit:Release Time) will change.
Attack time (Controller number 73)
Status
2nd byte
BnH
49H
n = MIDI channel number:
vv = Attack time value (relative change): 00H - 7FH (-64 - 0 - +63),
* The Attack Time parameter (EDIT:Tone Edit:Attack Time) will change.
Cutoff (Controller number 74)
Status
2nd byte
BnH
4AH
n = MIDI channel number:
vv = Cutoff value (relative change):
* The Cutoff parameter (EDIT:Tone Edit:Cutoff) will change.
Decay Time (Controller number 75)
Status
2nd byte
BnH
4BH
n = MIDI channel number:
vv = Decay Time value (relative change): 00H - 7FH (-64 - 0 - +63)
* The decay time will change in GM mode.
Vibrato Rate (Controller number 76)
Status
2nd byte
BnH
4CH
n = MIDI channel number:
vv = Vibrato Rate value (relative change): 00H - 7FH (-64 - 0 - +63)
* The vibrato rate will change in GM mode.
Vibrato Depth (Controller number 77)
Status
2nd byte
BnH
4DH
n = MIDI channel number:
vv = Vibrato Depth Value (relative change):00H - 7FH (-64 - 0 - +63)
* The vibrato depth will change in GM mode.
Vibrato Delay (Controller number 78)
Status
2nd byte
BnH
4EH
n = MIDI channel number:
vv = Vibrato Delay value (relative change):00H - 7FH (-64 - 0 - +63)
* The vibrato delay will change in GM mode.
Portamento Control (Controller number 84)
Status
2nd byte
BnH
54H
n = MIDI channel number:
kk = source note number:
* A Note-on received immediately after a Portamento Control message will change
continuously in pitch, starting from the pitch of the Source Note Number.
* If a voice is already sounding for a note number identical to the Source Note Number,
this voice will continue sounding (i.e., legato) and will, when the next Note-on is
received, smoothly change to the pitch of that Note-on.
* The rate of the pitch change caused by Portamento Control is determined by the
Portamento Time value.
Effect 1 (Reverb Send Level) (Controller number 91)
Status
2nd byte
BnH
5BH
n = MIDI channel number:
vv = Reverb Send Level:
* The Reverb Amount parameter (EDIT:Tone Edit:Reverb Amount) will change.
3rd byte
vvH
0H - FH (ch.1 - 16)
3rd byte
vvH
0H - FH (ch.1 - 16)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (-64 - 0 - +63)
3rd byte
vvH
0H - FH (ch.1 - 16)
3rd byte
vvH
0H - FH (ch.1 - 16)
3rd byte
vvH
0H - FH (ch.1 - 16)
3rd byte
vvH
0H - FH (ch.1 - 16)
3rd byte
kkH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
Effect 3 (Chorus Send Level) (Controller number 93)
Status
2nd byte
BnH
5DH
n = MIDI channel number:
vv = Chorus Send Level:
* The Chorus Amount parameter (EDIT:Tone Edit:Chorus Amount) will change.
RPN MSB/LSB (Controller number 100, 101)
Status
2nd byte
BnH
65H
BnH
64H
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are extended.
When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any
order) should be sent in order to select the parameter, then
Data Entry (Controller numbers 6 and 38) should be sent to set the value. Once RPN
messages are received, Data Entry messages that is received at the same MIDI channel after
that are recognized as changing toward the value of the RPN messages. In order not to
make any mistakes, transmitting RPN Null is recommended after setting parameters you
need.
This device receives the following RPNs.
RPN
Data entry
MSB, LSB
MSB, LSB
Notes
00H, 00H
mmH, llH
Pitch Bend Sensitivity
mm: 00H - 18H (0 - 24 semitones)
ll: ignored (processed as 00H)
Up to 2 octave can be specified in semitone steps.
* The Bend Range parameter (EDIT:Tone Edit:Bend
Range) will change.
00H, 01H
mmH, llH
Master Fine Tuning
mm, ll: 20 00H - 40 00H - 60 00H
(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)
* The Fine Tune parameter (EDIT:Tone Edit:Fine Tune)
will change.
00H, 02H
mmH, llH
Master Coarse Tuning
mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll: ignored (processed as 00H)
* The Coarse Tune parameter (EDIT:Tone Edit:Coarse
Tune) will change.
00H, 05H
mmH, llH
Modulation Depth Range
mm, ll: 00 00H - 06 00H ( 0 - 16384 * 600 / 16384 cent)
* The modulation depth range will change in GM mode.
7FH, 7FH
---, ---
RPN nul
RPN and NRPN will be set as "unspecified." Once this
setting has been made, subsequent Parameter values that
were previously set will not change.
mm, ll: ignored
Program Change
Status
2nd byte
CnH
ppH
n = MIDI channel number:
pp = Program number:
* Not received when the Rx Program Change parameter (EDIT:Internal Part Parameter:Rx
Program Chanage) is OFF.
Pitch Bend Change
Status
2nd byte
EnH
llH
n = MIDI channel number:
mm, ll = Pitch Bend value:
* Not received when the Rx Bender parameter (EDIT:Internal Part Parameter:Rx Bender)
is OFF.
MIDI Implementado
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
mmH
llH
0H - FH (ch.1 - 16)
00H - 7FH (prog.1 - prog.128)
3rd byte
mmH
0H - FH (ch.1 - 16)
00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
147
Tabla de contenido
