Tabla de contenido
MIDI Implementado
Panpot (Controller number 10)
Status
2nd byte
BnH
0AH
n = MIDI channel number:
vv = Panpot:
* These messases are transmitted when Pan value is set in MIDI Tx Mode.
Hold 1 (Controller number 64)
Status
2nd byte
BnH
40H
n = MIDI channel number:
vv = Control value:
* These messases are transmitted when Damper pedal is operated.
Portamento (Controller number 65)
Status
2nd byte
BnH
41H
n = MIDI channel number:
vv = Control value:
* These messases are transmitted when Portament Swicth is set in MIDI Tx Mode.
Sostenuto (Controller number 66)
Status
2nd byte
BnH
42H
n = MIDI channel number:
vv = Control value:
* These messases are transmitted when Foot Contolloer 2 is operated in One Touch Piano
Mode.
Soft (Controller number 67)
Status
2nd byte
BnH
43H
n = MIDI channel number:
vv = Control value:
* These messases are transmitted when Foot Contolloer 1 is operated in One Touch Piano
Mode.
Resonance (Controller number 71)
Status
2nd byte
BnH
47H
n = MIDI channel number:
vv= Resonance value (relative change):
* These messases are transmitted when Resonance value is set in MIDI Tx Mode.
Release Time (Controller number 72)
Status
2nd byte
BnH
48H
n = MIDI channel number:
vv = Release Time value (relative change): 00H - 7FH (-64 - 0 - +63)
* These messases are transmitted when Release Time is set in MIDI Tx Mode.
Attack time (Controller number 73)
Status
2nd byte
BnH
49H
n = MIDI channel number:
vv = Attack time value (relative change): 00H - 7FH (-64 - 0 - +63)
* These messases are transmitted when Attack Time is set in MIDI Tx Mode.
Cutoff (Controller number 74)
Status
2nd byte
BnH
4AH
n = MIDI channel number:
vv = Cutoff value (relative change):
* These messases are transmitted when Cutoff value is set in MIDI Tx Mode.
152
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 40H - 7FH (Left - Center - Right)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127) 0-63 = OFF, 64-127 = ON
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (-64 - 0 - +63)
3rd byte
vvH
0H - FH (ch.1 - 16)
3rd byte
vvH
0H - FH (ch.1 - 16)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (-64 - 0 - +63)
Effect 1 (Reverb Send Level) (Controller number 91)
Status
2nd byte
BnH
5BH
n = MIDI channel number:
vv = Reverb Send Level:
* These messases are transmitted when Reverb value is set in MIDI Tx Mode.
Effect 3 (Chorus Send Level) (Controller number 93)
Status
2nd byte
BnH
5DH
n = MIDI channel number:
vv = Reverb Send Level:
* These messases are transmitted when Chorus value is set in MIDI Tx Mode.
RPN MSB/LSB (Controller number 100, 101)
Status
2nd byte
BnH
65H
BnH
64H
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are extended.
When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any
order) should be sent in order to select the parameter, then
Data Entry (Controller numbers 6 and 38) should be sent to set the value. Once RPN
messages are received, Data Entry messages that is received at the same MIDI channel after
that are recognized as changing toward the value of the RPN messages. In order not to
make any mistakes, transmitting RPN Null is recommended after setting parameters you
need.
This device transmits the following RPNs.
RPN
Data entry
MSB, LSB
MSB, LSB
00H, 00H
mmH, llH
00H, 01H
mmH, llH
00H, 02H
mmH, llH
00H, 05H
mmH, llH
7FH, 7FH
---, ---
Program Change
Status
2nd byte
CnH
ppH
n = MIDI channel number:
pp = Program number:
* When Rec Mode is ON (EDIT:Utility:Rec Setting:Rec Mode), these messages are
transmitted when Tone is selected.
* These messages are transmitted when Program Change parameter is Set on MIDI Tx
Part.
Pitch Bend Change
Status
2nd byte
EnH
llH
n = MIDI channel number:
mm, ll = Pitch Bend value:
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
mmH
llH
Notes
Pitch Bend Sensitivity
mm: 00H - 18H (0 - 24 semitones)
ll: ignored (processed as 00H)
Master Fine Tuning
mm, ll: 20 00H - 40 00H - 60 00H
(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)
Master Coarse Tuning
mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll: ignored (processed as 00H)
Modulation Depth Range
mm, ll:00 00H - 06 00H
(0 - 16384 x 600 / 16384 cent)
RPN null
RPN and NRPN will be set as "unspecified."
Once this setting has been made, subsequent
0H - FH (ch.1 - 16)
00H - 7FH (prog.1 - prog.128)
3rd byte
mmH
0H - FH (ch.1 - 16)
00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
Tabla de contenido
