Service And Maintenance; Push Stick - Festool PRECISIO CS 70 EBG Manual De Instrucciones Original

9.1d Featherboard
NOTE
Use a featherboard for non-through cuts. Fit the
featherboard on the fence and the table so that the
featherboard pushes the workpiece down firmly
onto the plate during cutting. Featherboards are
not included with the delivery.
9.1e Longitudinal cuts at an angle
fOnly use the left fence when making longitu-
dinal cuts at an angle in material with an edge
length of ≤ 150 mm. This creates more space
between the fence and the saw blade.
9.2 Using the machine as a circular trim-
ming saw
9.2a Cross cuts
fPlace the saw blade in the back table position,
see section 8b.
fUse the preset profile setting rail as a crosswi-
se or angle ruler (fig. 3) to position the work-
piece and hold it in place. Fastening clamps
(not included) can be inserted into the groove
[3-8] to secure the workpiece.
Make the saw cut:
fFirst release the saw lock by turning the rotary
knob [2-6] anticlockwise.
fPull the saw forward using the same rotary
knob [2-6].
fAfter completing the cut, move the saw unit
right back to its starting position before re-
moving the workpiece from the preset profile
setting rail.
NOTE
To ensure that the control elements are easy to
access for adjusting the saw settings, the saw
can be locked in the middle position by pushing
the notch lever [1-9] down. Turn the rotary knob
[2-6] anticlockwise to release the lock again.
9.2b Angled cuts
The mitre angle of the saw blade needs to be ad-
justed for angled cuts, see section 8.7. The pre-
set profile setting rail is on the right-hand side
of the table.
The preset profile setting rail needs to be adjust-
ed for mitre cuts, see section 8.10.

9.3 Push stick

Place the push stick [11-2] in the accessory hol-
der [11-4] when not in use.
10

Service and maintenance

WARNING
Risk of accident, electric shock
fAlways disconnect the mains plug before
maintaining, servicing or making any kind of
adjustment.
fAll maintenance and repair work which re-
quires the motor housing to be opened should
always be carried out by an authorised ser-
vice workshop.
fDamaged safety devices and components
must be repaired or replaced in a recognised
specialist workshop in accordance with re-
gulations, unless otherwise indicated in the
operating manual.
Customer service and repairs: Only by
manufacturer or service workshops. Find
the nearest address at: www.festool.com/
service
Always use original Festool spare parts.
EKAT
4
Order no. at www.festool.com/service
5
3
2
1
The machine is equipped with special self-dis-
connecting carbon brushes. If they wear out, the
power supply is disconnected automatically and
the tool stops.
Maintain your machine regularly to make sure it
functions properly:
- Use an extractor to remove dust deposits.
- Keep the guide rods clean and grease them
regularly.
- Keep the toothed gears behind the rotary han-
dle [2-3] clean.
- Replace worn or damaged table inserts [1-7].
- If wood chips block the extraction channel on
the bottom guard, unscrew the rotary knob
[5-8] and move the flap [5-6] approx. 8 mm
to open up a gap so that the blockage can be
removed.
- If the blockage is serious or the saw seizes
when the initial cut is made, use the hex key
to unscrew the fasteners [5-7] so that the flap
[5-6] can be opened completely. Close the flap
again prior to use.
- After completing work, wind the power cable
[11-1] around the accessory holder [11-4].
- A damper allows the saw unit to retract evenly
along the entire cutting length. If this is not the
case, the damper can be adjusted using the hole
-
P R E C I S I O GB
33