Parts Of The Machine; Intended Use; General Safety Instructions; Safety Instructions For Table Saws - Festool PRECISIO CS 70 EBG Manual De Instrucciones Original

3

Parts of the machine

The specified illustrations appear at the begin-
ning of this operating manual.
[1-1] Foldaway legs
[1-2] On/off switch
[1-3] Extra feet
[1-4] Clamping screws
[1-5] Fence position marking
Preset profile setting rail position marking
[1-6]
Table insert
[1-7]
Guard
[1-8]
Notch lever
[1-9]
[1-10] Cutting height setting
[1-11] Knobs for adjusting the foldaway legs
[1-12] End cap
[1-13] Handle area
4

Intended use

The PRECISIO is designed as a transportable
power tool for sawing wood, plastics, panel ma-
terials made of wood and similar materials.
When fitted with the special saw blades for alumin-
ium that are offered by Festool, these machines
can also be used for sawing aluminium. Materials
containing asbestos must not be processed.
The user is liable for damage and acci-
dents caused by improper and non-intended use.
5 Safety instructions
5.1

General safety instructions

WARNING!
gs, instructions, illustrations and specifications
provided with this power tool. Failure to follow
all instructions listed below may result in electric
shock, fire and/or serious injury.
Keep all safety information and instructions for
future reference.
The term "power tool" used in the safety instruc-
tions refers to mains-powered power tools (with
power cable) or battery-powered power tools
(without power cable).
5.2

Safety instructions for table saws

Guarding related warnings
a. Keep guards in place. Guards must be in
working order and be properly mounted. A
guard that is loose, damaged, or is not func-
tioning correctly must be repaired or replaced.
Read all safety warnin-
b. Always use saw blade guard and riving knife
for every through–cutting operation. For
through-cutting operations where the saw
blade cuts completely through the thickness
of the workpiece, the guard and other safety
devices help reduce the risk of injury.
c. Immediately reattach the guarding system af-
ter completing an operation (such as rabbet-
ing, dadoing or resawing cuts) which requires
removal of the guard and/or riving knife. The
guard, riving knife, and anti-kickback device
help to reduce the risk of injury.
d. Make sure the saw blade is not contacting the
guard, riving knife or the workpiece before
the switch is turned on. Inadvertent contact
of these items with the saw blade could cause
a hazardous condition.
e. Adjust the riving knife as described in this
instruction manual. Incorrect spacing, po-
sitioning and alignment can make the riving
knife ineffective in reducing the likelihood of
kickback.
f. For the riving knife to work, it must be en-
gaged in the workpiece. The riving knife is
ineffective when cutting workpieces that are
too short to be engaged with the riving knife.
Under these conditions a kickback cannot be
prevented by the riving knife.
g. Use the appropriate saw blade for the riving
knife. For the riving knife to function properly,
the saw blade diameter must match the ap-
propriate riving knife and the body of the saw
blade must be thinner than the thickness of
the riving knife and the cutting width of the
saw blade must be wider than the thickness
of the riving knife.
Cutting procedures warnings
a. DANGER: Never place your fingers or
hands in the vicinity or in line with the
saw blade. A moment of inattention or
a slip could direct your hand towards the
saw blade and result in serious personal inju-
ry.
b. Feed the workpiece into the saw blade or
cutter only against the direction of rotation.
Feeding the workpiece in the same direction
that the saw blade is rotating above the table
may result in the workpiece, and your hand,
being pulled into the saw blade.
-
P R E C I S I O GB
23