Manufacturer's Warranty; Spare Parts Lists - REMS Multi-Push SL Instrucciones De Servicio

Ocultar thumbs Ver también para Multi-Push SL:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 50
eng
5.5. Fault: The set pressure (p refer) is not established in the test with water program (Multi-Push SLW).
Cause:
● The water pressure of the house connection is greater than the set pressure
(p refer).
● Suction/pressure hose (Fig. 1 (13)) or high-pressure hose (Fig. 4 (26))
leaking.
● Hydro-pneumatic pump does not build up pressure.
● Stop tap of the water supply is closed or only partly open.
● No or too little air pressure in the compressed air tank.
●  Electronic flushing and pressure testing unit with compressor defective.
5.6. Fault: The pressure in the pipe to be tested is not relieved after running the test with water programs or during the test with water B, P+M.
Cause:
● Pressure relief water drain (Fig. 4 (27)) is soiled or defective.
●  Electronic flushing and pressure testing unit with compressor defective.
5.7. Fault: No or too little dosing solution pumped out of the bottle.
Cause:
● Unsuitable disinfectant, cleaning, preserving agent.
● Disinfection and cleaning unit not connected to the Multi-Push properly.
● Disinfection and cleaning unit soiled.
● Disinfection and cleaning unit defective.
5.8. Fault:  The date and time must be reset every time the electronic flushing and pressure testing unit with compressor is switched on.
Cause:
● Battery depleted.
5.9. Fault: The new version software was not installed.
Cause:
● USB stick not recognised.
● New version software is not on the USB stick.
● The USB stick was pulled out of the USB port
(Fig. 2 (33)) during the installation.
● A folder was created on the USB stick and the new version software was
copied into this folder.
5.10. Fault:  The flushing and testing programs have been incorrectly displayed on the PC.
Cause:
● The font "Lucida Console" is required for a correct display.
5.11. Fault: Printing on paper weak or illegible. Printout aborted prematurely.
Cause:
● Weak battery charge.
● Paper reel inserted incorrectly in printer.
● The printer can only be used as of Version Software 2.0.
6. Disposal
The electronic flushing and testing unit with compressor as well as the disin-
fection, cleaning and preservation media may not be thrown in the domestic
waste at the end of their useful life. They must be disposed of according to the
legal regulations.
7. Manufacturer's Warranty
The warranty period shall be 12 months from delivery of the new product to the
first user. The date of delivery shall be documented by the submission of the 
original purchase documents, which must include the date of purchase and the
designation of the product. All functional defects occurring within the warranty
period, which are clearly the consequence of defects in production or materials,
will be remedied free of charge. The remedy of defects shall not extend or
renew the warranty period for the product. Damage attributable to natural wear
and tear, incorrect treatment or misuse, failure to observe the operational
instructions, unsuitable operating materials, excessive demand, use for unau-
thorized purposes, interventions by the customer or a third party or other
reasons, for which REMS is not responsible, shall be excluded from the warranty
Services under the warranty may only be provided by customer service stations
authorized for this purpose by REMS. Complaints will only be accepted if the
product is returned to a customer service station authorized by REMS without
prior interference in an unassembled condition. Replaced products and parts
shall become the property of REMS.
The user shall be responsible for the cost of shipping and returning the product.
The legal rights of the user, in particular the right to make claims against the
seller under the warranty terms, shall not be affected. This manufacturer's
warranty only applies for new products which are purchased in the European
Union, in Norway or in Switzerland.
Remedy:
● Close the shut-off valve of the house connection.
● Change suction/pressure hose or high-pressure hose.
● Connect suction/pressure hose between the house connection and the
pressure test with water supply, see 2.6.2.
● Fully open the stop tap.
● Hydro-pneumatic pump requires compressed air, see 5.2. Fault:
●  Have the electronic flushing and pressure testing unit with compressor 
checked/repaired by an authorised REMS customer service workshop.
Remedy:
●  Clean the pressure relief water drain or have it replaced by qualified personnel 
or an authorised REMS customer service workshop.
●  Have the electronic flushing and pressure testing unit with compressor 
checked/repaired by an authorised REMS customer service workshop.
Remedy:
● Use REMS Peroxi Color, REMS CleanH, REMS NoCor.
● See flow direction arrow, see also 2.5.
● Clean disinfection and cleaning unit, see also 4.1.
● Have disinfection and cleaning unit checked/repaired by an authorised REMS
customer service workshop.
Remedy:
● Change battery. See 4.2.
Remedy:
● Use another USB stick.
● Copy new version software to the USB stick.
● Repeat the procedure described in 2.3.. Use a USB stick with a LED if
possible.
● Move the new version software into the main directory of the USB stick.
Remedy:
● Select font "Lucida Console", install if necessary.
Remedy:
● Charge battery.
● Insert paper roll, see 3.6.
●  Load software by USB stick as a download under www.rems.de → Downloads 
→ Software into the controller of the REMS Multi-Push, see 2.3.
This warranty is subject to German law with the exclusion of the United Nations
Convention on Contracts for the International Sales of Goods (CISG).

8. Spare parts lists

For spare parts lists, see www.rems.de → Downloads → Parts lists.
eng
25
Tabla de contenido
loading

Este manual también es adecuado para:

Multi-push slw

Tabla de contenido