Manufacturer's Warranty - REMS MSG 25 EE Manual De Instrucciones

eng
diately before welding, the end of the pipe and interior of the sleeve
and, if necessary, the heating spigot and socket should be cleaned
with non-adherent paper or a non-fraying cloth and spirit or industrial
alcohol. In particular, no remnants of plastic must be left adhering to
the coating on the heating spigot or socket. When cleaning the wel-
ding tools, take care to ensure without fail that their anti-adhesive coa-
ting is not damaged by tools. The welding surfaces must not be tou-
ched again before welding takes place.
3.3. Welding process stages
3.3.1. Heating-up
For the heating-up process, the pipe and moulding are pushed axial-
ly onto the welding tools in a continuous movement until they reach
the stop or the marking on the tools. The heating-up time specified in
Fig. 5, colunn 2 must be observed. During the heating process, heat
penetrates into the joint faces and brings them up to welding tempe-
rature.
3.3.2. Changeover and joining
After the heating process, the pipe and moulding are pulled away from
the welding tools in a series of jerks and pushed together, without twi-
sting, as far as they will go. The changeover time specified in Fig. 5,
column 3 must not be exceeded, otherwise the joint faces will cool to
an impermissible extent.
3.3.3. Setting
The joint must be allowed to set (i.e. held) in accordance with the da-
ta given in Fig. 5, column 4.
3.3.4. Cooling
The joint must not be subjected to the stresses imposed by further pi-
pe-laying operations until the cooling-off period (Fig. 5, column 5) has
expired.
4. Maintenance
Before undertaking any maintenance or reparis, disconnect the unit from
the mains. Operations of this nature must not be carried out other than by
qualified, trained personnel.
4.1. Maintenance
REMS MSG units are entirely maintenance-free.
4.2. lnspection/repairs
The anti-adhesive coating on the heating element must be cleaned
with non-adherent paper or a non-fraying cloth and spirit or industrial
alcohol before each welding process. Any remnants of plastic adhe-
ring to the heating element must be cleaned off in the same way. In
this process, take care to ensure that the anti-adhesive coating on the
heating element is not damaged by tools.
5. Action in Case of Trouble
5.1. Trouble
Sleeve welding unit does not heat
Cause
Sleeve welding unit is not plugged in
•
Mains lead is defective
•
Mains socket is defective
•
Unit is defective
•
5.2. Trouble
Plastic remnants stick onto the heating tools
Cause
Heating tools are dirty (see 4.2.)
•
Anti-adhesive coating is damaged
•

6. Manufacturer's Warranty

For improper used and subsequently damaged PTFE-coatings of the
heated tool no guarantee will be granted.
The warranty period shall be 12 months from delivery of the new pro-
duct to the first user but shall be a maximum of 24 months after delivery
to the Dealer. The date of delivery shall be documented by the submis-
sion of the original purchase documents, which must include the date
of purchase and the designation of the product. All functional defects
occurring within the warranty period, which clearly the consequence of
defects in production or materials, will be remedied free of charge. The
remedy of defects shall not extend or renew the guarantee period for
the product. Damage attributable to natural wear and tear, incorrect tre-
atment or misuse, failure to observe the operational instructions, un-
suitable operating materials, excessive demand, use for unauthorized
purposes, interventions by the Customer or a third party or other rea-
sons, for which REMS is not responsible, shall be excluded from the
warranty.
Services under the warranty may only be provided by customer servi-
ce stations authorized for this purpose by REMS. Complaints will only
be accepted if the product is returned to a customer service station autho-
rized by REMS without prior interference in an unassembled condition.
Replaced products and parts shall become the property of REMS.
The user shall be responsible for the cost of shipping and returning the
product.
The legal rights of users, in particular the right to claim damages from
the Dealer, shall not be affected. This manufacturer's warranty shall ap-
ply only to new products purchased in the European Union, in Norway
or Switzerland.
P.S.
Various figures and statements in this operating manual are taken from the
DVS directions 2207 and 2208 (DVS: German Association of Welding Tech-
nology, Düsseldorf).
eng