Idiomas disponibles
Idiomas disponibles
9.4 Fitting the table inlay (fig. 16)
1.
Place the table inlay (4) in the recess.
2.
Tighten the fixing screw (4a) by turning it a quarter
turn clockwise.
9.5 Fitting the saw blade guard (fig. 19)
1.
Place the saw blade guard (2) onto the riving knife
(3) from above so that the fixing screw (2a) fits
through the hole in the riving knife.
2.
Tighten the fixing screw (2a).
Attention! The saw blade guard (2) must remain
free to move.
3.
Ensure that the saw blade guard (2) can move
freely.
4.
Disassembly takes place in reverse order.
m WARNING
Danger of injury due to incorrect fitted saw blade guard
-
Before starting sawing, ensure that the saw
blade guard (2) lowers automatically onto the
material to be sawn.
9.5.1 Checking the saw blade guard
After fitting, check that the saw blade guard (2) is func-
tioning properly.
1.
Lift the saw blade guard (2) and then release it.
2.
The saw blade guard (2) should move back to its
starting position automatically.
9.6 Fitting the parallel stop (fig. 20)
1.
First place the parallel stop (8) with open eccentric
lever (8b) on the rear guide rail (7a), then on the
front guide rail (7b) on the saw table (5).
2.
To change the position of the parallel stop (1), slide
the parallel stop (1) with open eccentric lever (8b)
along the front and rear guide rail (7a/7b).
3.
To secure the parallel stop (1) in the desired po-
sition, press the eccentric lever (8b) fully down-
wards.
9.6.1 Attaching the stop rail to the parallel stop
(fig. 21 + 22)
1.
Insert the two coach bolts M6 x 55 mm (E) from the
inside into the parallel stop (8) and secure them
with the two knurled nuts (G).
Attention! Do not tighten the knurled nuts (G) yet.
(fig. 21)
2.
Push the stop rail (8a) through the two coach
bolts (E) into the desired position and tighten the
knurled nuts (G). (fig. 22)
44 | GB
9.7 Fitting the transverse stop (fig. 23)
1.
Push the transverse stop (19) into the groove (28)
of the sliding carrier plate (21).
2.
Now place the guide rail (19b) including the screws
into the marked grooves of the transverse stop (19)
(fig. 23)
3.
Move the guide rail (19b) into the desired position
and tighten the knurled nut (19d).
4.
Screw the clamping handle (19c) into the trans-
verse stop (19) by turning this clockwise.
To change the angle of the transverse stop (19), pro-
ceed as follows:
1.
Loosen the clamping handle (19c) by turning it
counterclockwise.
2.
Turn the transverse stop (19) until the arrow points
to the required angle.
3.
Secure this position by turning the clamping han-
dle (19c) clockwise.
9.8 Connecting a suction system (fig. 24 + 25)
m WARNING
Danger of injury for eyes due to swirling chips
-
Wear eye protection.
-
Only operate the product with a suitable chip ex-
traction system. Do not use household vacuum
cleaners.
1.
Use an M5 x 10mm Phillips screw (F), two small
washers (H) and an M5 nut (M) to screw the suc-
tion hose clamp (23) into the right table width ex-
tension (9). (fig. 24)
2.
Connect the suction hose (6) to the suction port
(22) on the back of the machine, push through the
suction hose clamp (23) and connect to the suction
port of the saw blade guard (2). (fig. 25)
3.
Connect a suitable chip extraction system (not in-
cluded in the scope of delivery) to the suction port
(22).
ATTENTION
Check and clean the extraction channels at regular
intervals.
10. Before commissioning
10.1 General notes
• Check that the product is fully assembled.
• Check that the safety covers are present, installed
and functional.
• Check that the switches work as intended.
www.scheppach.com
