Maintenance; Replacing The Filter; Descaling - Bluewater RO 300 Manual Del Usuario

The indicator light on the faucet (fig. 1) indicates the
following:
GREEN lIGHT
YEllOW lIGHT
FlASHING YEllOW
lIGHT
It can take up to 120 seconds before good water quality
is indicated on the pure water faucet.
The water purifier is most efficient when producing pure
water for longer periods, e.g. filling a whole jug rather
than a drinking glass.

RePlacing the filteR

It is important to pay attention to filter replacement, as the
filter's primary job is to protect the membrane. Check that the
container is not leaking after filter replacement, and perform
follow-up checks.
Replace the filter when:
• The filter light flashes or lights
• The water purifier emits a noise
• The flow is reduced by half
Illustrations, see fig. 3
1. Check that the water purifier is in standby mode.
Press and hold in the service button, using a pen,
until the service light comes on (approx. 6 seconds).
Release the button. The lights on the faucet now
flashes rapidly for 15 seconds. This procedure will
prevent flushing from taking place during filter
replacement.
2. Open the front cover using the grip, as illustrated.
3. Lift the lock plate on the filter cover and unscrew the
container. Use the supplied filter spanner if neces-
sary. Remember that the container is full of water
and that it can overflow!
. Remove the old filter.
5. Wipe up any spillage on the base plate.
6. Clean the filter container with a brush and water.
7. Insert the new filter with the pin pointing up. Fill up
the container with water to the lowest thread.
8. Screw back the filter container. Tighten the filter con-
tainer until the locking plate clicks into the groove.
Do not tighten any more.
9. Close the front cover.
10. Reset the filter indicator by pressing in the filter but-
ton and keeping it pressed until the filter light goes
out (approx. 3 seconds). Use a pen.
The filter replacement is now complete and the water
purifier is ready to be used.
FIlTER REPlACEMENT BEFORE INDICATION
If the filter is replaced before the light indicates that replace-
ment is necessary, reset in accordance with step10. The only
difference is that the filter light first comes on and then go out.
using the WateR PuRifieR
Good water quality.
Unsatisfactory water quality.
Control panel attracting your
attention.

maintenance

autOmatic flushing
• When the combined drawing time has been longer than 60
seconds, an automatic flush is performed.
• If pure water production has lasted for more than
2 hours (RO300C) / 10 min (RO300), the water purifier
automatically stops, flushes and goes into standby mode.
The flushing procedure takes 5 minutes and cannot be inter-
rupted.
• When the water purifier is connected to water and electricity,
flushing is automatically performed 6 hours after the most
recent flush.

descaling

When the flow is reduced, the water purifier should be des-
caled to extend its lifetime. When the flow cannot be restored
despite descaling and filter replacement, contact your dealer.
During the descaling procedure, which takes around 10 hours,
the water purifier cannot be used. The descaling product can be
ordered from your dealer, see «Consumables».
The descaling product must be kept out of the reach
of children! Wash your hands after using it.
1. Check that the water purifier is in standby mode.
2. Press the service button, using a pen, until the
service light comes on. Release the button. The light
on the faucet now flashes rapidly for 15 seconds.
This will prevent flushing from taking place during
descaling.
3. Unscrew the filter container in accordance with
«Replacing the filter», points 2 - 5. Remove the filter
and put it a side.
. Mix 50 g (approx. 1/ of the bag) of the descaling
product with 7 dl of lukewarm water. Stir until the
powder has dissolved.
5. Screw the filled container in place.
6. Start the water purifier and produce pure water for
30 seconds.
7. While production is still in progress, pull out the
plug, see fig. .
8. Allow the water purifier to stand for approx. 10
hours (e.g. overnight).
9. Undo the container and empty the water. Replace
the filter in accordance with «Replacing the filter»,
points 7 - 8, except that the previously used filter is
used here.
10. Close the front cover and connect the plug.
11. Flush the water purifier in accordance with «Flush-
ing».
Do not use the purified water until flushing is
complete.
The descaling process is now finished. The water
purifier is ready to be used.
EN