Tabla de contenido
Idiomas disponibles
Idiomas disponibles
cOnnecting the WateR PuRifieR
Before the water purifier is placed in its intended position,
remove the plug at the end of the reject water hose and the two
plugs in the connections on the purifier, see fig. 13. Connect the
two hoses and the faucet cord to the appliance as shown in
fig. 1.
feed WateR
1.
Screw the bent end of the feed water hose onto the
water purifier. Check that the seal is in place in the
connection. See fig. 1 (1).
2.
Open the shut-off valve on the feed water and check
that there is no leakage at the feed water hose.
PuRe WateR
The pure water is routed via the pure water hose to the faucet
installed on the sink unit.
1.
Connect the pure water hose from the pure water
faucet to the water purifier.
2.
Push the hose into the bottom position, up to the
mark (approx. 19 mm), see fig. 1 (2).
Reject WateR
The reject water hose has already been connected to the water
purifier on delivery. The other end of the hose is connected to
the waste water pipe.
indicatOR light
1.
Connect the cable from the faucet indicator light, as
shown in fig. 1 (3).
2.
Place the water purifier in the intended position.
electRical cOnnectiOn
The water purifier should be connected to an earthed electrical
supply (230 V, 50 Hz and 10 A). We recommend connection
using a plug, as some operations require the power supply to be
temporarily interrupted. The plug should also be easily acces-
sible after installation.
1.
Connect the plug to the earthed wall socket.
2.
The water purifier starts and flushes for 90 seconds.
Flushing is performed every time the plug is con-
nected.
Do not drink the water until the flushing procedure
under «Flushing» has been completed.
installatiOn
flushing
Flushing should take place when the water purifier:
•
Is new and has never been used before.
•
Is reinstalled after having been stored/protected against
freezing.
•
Has been cleaned, in order to rinse out the detergent.
•
Has been fitted with a new membrane.
Do not use the pure water until flushing is complete.
FIRST, CHECK THAT:
•
The shut-off valve on the feed water is open.
•
The connection for the feed water is watertight.
•
The reject water outlet and pure water connections are
watertight.
•
The filter container is properly tightened.
•
There is no leakage from the connections during flushing. In
the event of leakage, pull out the plug and fix the leak. Con-
nect the plug and perform flushing again as described below.
1.
Check that the water purifier is in standby mode.
2.
Press the service button, using a pen, until both the
service and filter lights come on (approx. 15 sec-
onds). The lights on the faucet now flashes rapidly.
3.
Release the button. The flushing procedure is now
performed and takes 25 minutes. Water will be puri-
fied at the end of the procedure.
This water must not be used!
.
When the flushing procedure is complete, the lights
on the faucet goes out. The water purifier is now
ready to be used.
mOving the WateR PuRifieR
If you move the purifier from one place to another, you should
remember the following points:
•
Close the shut-off valve for the feed water before removing
the feed water hose.
•
Pull out the plug.
•
Always transport the appliance upright.
•
Install in accordance with the installation instructions.
If the water purifier will not be used for four months or more,
or if it is to be disconnected from the water and electricity for
several days, it should be put into storage, see «Storage».
EN10
Capítulos
Tabla de contenido
