Technical Specifications - Nice Ten TNKCE Instrucciones Y Advertencias Para El Instalador

8) Technical specifications

For purposes of product improvements, Nice S.p.a. reserves the right to apply modifications to technical specifications at any time when
deemed necessary, while maintaining the same functionalities and intended use.
All technical specifications stated in this section refer to an ambient temperature of 20°C (± 5°C).
Technical specifications: TEN
Model
Type
Maximum start-up torque
Nominal torque
Speed under no-load
Speed at nominal torque
Maximum frequency of operating cycles *
(the control unit limits cycles to the maximum
value specified in tables 3 and 4)
Maximum continuous operation time
(the control unit limits continuous operation to
the maximum value specified in tables 3 and 4)
Limits of use
Durability
TEN Power supply
TEN/V1 Power supply
Maximum power absorption with 1 motor
Maximum power absorption with 2 motors
Insulation class
Buffer battery power
Courtesy light
Flashing light Output
Phototest/electric lock output
STOP input
SS input
Radio AERIAL input
Radio receiver
Programmable functions
Functions in self-learning mode
Operating temperature
Use in particularly acid, saline or potentially
explosive environments
Protection rating
Dimensions and weight
Weight
* At 50°C the maximum operating frequency is (cycles/hour):
** At 50°C the maximum continuous operation time is (minutes):
TN2020 TN2030
Electromechanical gearmotor for the automatic movement of pro-
/ jecting and non-projecting up-and-over doors for residential use,
complete with electronic control unit
320 Nm 320 Nm
220 Nm 220 Nm
1.7rpm; the control unit enables program-
1.4 (24Vcc) ming of the 2 following speeds: 1rpm or
1.7rpm
0.9 (24Vcc)
25 cycles / hour 20 cycles / hour
14 minutes 11 minutes
In general TEN is able to automate balanced doors with surface areas
up to 8m 2 with 1 motor and up to 14m
its specified in table 2.
Estimated between 10.000 cycles and 50.000 cycles according to conditions specified in
table 5
24 Vcc (-30% +50%)
130 W (5.5A) 220 W (1A)
III
12V/10W fitting BA15S
For 1 flashing light model LUCYB; MLB or
/
MLBT (lamp 12V, 21W)
/
For normally closed and normally open con-
tacts or with constant resistance of
/
8,2Kohm; in self-learning mode (a status
variation generates the "STOP" command)
For normally open contacts (closure of the
/
contact generates the SS command)
/ 52 ohm for cable type RG58 or similar
/
3 ON-OFF type functions and 3 adjustable
/
functions (see tables 15 and 17)
Self-learning of "STOP" type device (contact
type NO, NC or resistance 8,2KΩ). Self-
/ learning of door opening and closing posi-
tions and calculation of deceleration and par-
tial open points
-20°C ÷ 50°C
512 x 150 h 158
7.2 Kg
TN2020
TNKCE
280 Nm
200 Nm
1.2rpm
15 cycles / hour
10 minutes
2 with 2 motors, within the lim-
230Vac (-10% +15%)
50/60Hz.
120Vac (-10% +15%)
50/60Hz.
200 W (0.9A)
I I
no
24Vac /2W
Built-in
No
IP 44
9.5 Kg 15.5 Kg
TN2030 TNKCE
"6" "4" "4"
"6" "5" "5"
GB
TN2030+TN2020
420 Nm
280 Nm
10 cycles / hour
8 minutes
330 W (1.4A)
I
TN2030+TN2020
"3"
"4"
25