Fork Installation - Rock Shox Totem Lyrik Manual Del Usuario

English

ForK insTaLLaTion

It is extremely important that your RockShox fork is installed correctly by a qualified bicycle mechanic.
Improperly installed forks are extremely dangerous and can result in severe and/or fatal injuries.
1. Remove the existing fork from the bicycle and the crown race from the fork. Measure the length of the
fork steerer tube against the length of the RockShox steerer tube. The RockShox steerer tube may
need cutting to the proper length. Make sure there is sufficient length to clamp the stem (refer to the
stem manufacturer's instructions). After cutting steerer tube, install star-nut or headset compression
device.
w A R N I N G
DO NOT ADD THREADS TO ROCKSHOX THREADLESS STEERERS
THE STEERER TUBE CROWN ASSEMBLY IS A ONE-TIME PRESS FIT.
REPLACEMENT OF THE ASSEMBLY MUST BE DONE TO CHANGE THE
LENGTH, DIAMETER OR HEADSET TYPE (THREADED OR THREADLESS).
DO NOT REMOVE OR REPLACE THE STEERER TUBE. THIS COULD RESULT
IN THE LOSS OF CONTROL OF THE BICYCLE WITH POSSIBLE SERIOUS
AND/OR FATAL INJURIES.
. Install the headset crown race (9.8 mm for 1 1/" steerer, 9.9 mm for 1 1/8" steerers) firmly against
the top of the fork crown. Install the fork assembly on the bike. Adjust the headset until you feel no
play or drag.
. Install the brakes according to the manufacturer's instructions and adjust brake pads properly. Use the
fork only with disc style brakes mounted through the provided mounting holes. Do not use any cantilever
brake other than those intended by the brake manufacturer to work with a hangerless brace.
4. Follow the installation instructions that follow for the Maxle Quick Release System.
5. Keep in mind tire clearance as you choose tires. Maximum size is:
FORk
LYRIK
TOTEM
Be sure to check this diameter whenever you change tires. To do this, remove air pressure from the fork
and compress completely to make sure at least 5 mm of clearance exists between the top of the inflated
tire and the bottom of the crown. Exceeding maximum tire size will cause the tire to jam against the
crown when the fork is fully compressed.
4
Totem and Lyrik User Manual
MAx TIRE SIzE (INSTALLED)
.7"
.7"
95-4015-010-000, Rev. F
Totem and Lyrik User Manual
MaXLE 360° QuiCK rELEasE sYsTEM
I M P O R T A N T
CONSUMER SAFETY INFORMATION
The maxle quick release system allows the use of a standard 0 mm x 110 mm
thru-axle hub for enhanced stiffness. The axle threads into the left fork leg tightening
the hub against the left drop out. The axle is fixed in place in the lower leg by the maxle
quick release lever.
Riding with an improperly installed wheel can allow the wheel to move or disengage
from the bicycle, causing damage to the bicycle, and serious injury or death to the rider.
It is essential that you:
• Ensure that your axle, dropouts, and quick release mechanisms are clean and free
of dirt or debris.
• Ask your dealer to help you understand how to properly secure your front wheel
using the Maxle Quick Release System.
• Apply the correct techniques when installing your front wheel.
• Never ride your bicycle unless you are sure the front wheel is installed properly
and secure.
insTaLLaTion
Position your wheel in the dropouts of the lower leg. The hub should seat firmly in the dropouts. Be
sure to position the disk brake rotor in the caliper. Verify that neither the rotor, hub, nor rotor bolts
interfere with the lower legs. If unfamiliar with adjusting your disc brakes, see your brake manufacturer's
instruction.
TIGHTEN
1. Place Maxle lever in the open position (Fig. A). Ensure the lever
engages with the corresponding slot in the axle.
. Slide the axle through the right side of the hub until it engages the
threads of the left drop out.
. To tighten the axle into the dropout, turn the axle lever clockwise until
hand tight.
:
note never use any other tool to tighten the axle into the lower leg
-
over tightening of the axle can damage the axle and
w A R N I N G
DIRT AND DEBRIS CAN ACCUMULATE BETWEEN THE DROPOUT OPENINGS.
ALWAYS CHECK AND CLEAN THIS AREA WHEN REINSTALLING THE WHEEL.
ACCUMULATED DIRT AND DEBRIS CAN COMPROMISE THE SECURITY OF
THE AXLE, LEADING TO SERIOUS AND/OR FATAL INJURY.
SECURE
1. To lock the axle into the lower leg, close the Maxle quick release lever.
. The quick release mechanism is an "over-center cam", similar to the quick release found on many
bicycle wheels. When closing the lever, tension should be felt when the quick release lever is in the
© SRAM Corporation • 008
English
.
Fig. A
/ .
or the lower leg
5