Alarm Status - Bentel Security FC500 Manual Del Usuario

n ALARM STATUS
In the ALARM status, at least an alarm has been gene-
rated by a detector.
ALARM status will also be signalled by:
Ø blinking ALARM LEDs;
Ø on fire control panel Display;
Ø an intermittent audible signal on the fire control panel;
Ø the Alarm output points;
Figure 43 shows the Alarm status of fire control panel.
In this phase:
Alphanumeric keypad No function is related to
Alphanumeric keypad.
Cursor keys Use the UP Key to view the previous sto-
red event, if present;
Use the DOWN Key to view the next stored event, if
present.
Use the RIGHT Key to view the next string of data.
Use the LEFT Key to view the previous string of data.
ESC Key Use ESC key to cancel the operation and to
step back to main page.
ENTER Key The ENTER Key blocks/reactivates the
exchange between the labels of the devices and those
of the zones. When the block is enabled, the @ charac-
ter appears in the top left-hand corner of the display.
Function Key The F1 key shows the status of the SW
zones in alarm mode;
The F2 key activates the device status page, if the first
alarm is caused by a device connected to the control
panel (see note*);
The F3 key activates the device status page, if the last
alarm is caused by a device connected to the control
panel (see note*);
The F4 key activates the view of events stored in the
memory; if the stored alarms is caused by a device con-
nected to the control panel, pressing F4 again will take
you to the device status page (see note*).
Last Alarm
Figure 44 DISPLAY: ALARM STATUS.
The same NOTE (2) of the Warning status will function for the Alarm status.
40
First Alarm Alarm number
Total :0015
First : Centrale Master
Last : MS:Loop 1 mod182
#0011 : MS:Loop 2 det034
Stored Alarm
index
If the events are linked to
the devices, the zone label
alternates with the point
label every 5 seconds
Zones:004/Dev:013
First Z001 det.: Office 3, south wing
Last
Z001
det.: Main corridor, north
#0012 Z015 mod.: Air compressor room
Analogue Fire Panels
Total :0015
First : Z001
Last : Z002
#0011 : Z015
Total :0015
First : Z001
Last : Z001
#0011 : Z015
Total :0015
First : cause:
Last : cause: CP820
#0011 : cause: 801PH
Total :0015
First : Time: 10:46:21
Last : Time: 10:47:18
#0011 : Time: 10:47:12
Figure 43 Alarm status- Scrolling Right key
From Figure 43, in the ALARM STATUS, use the
RIGHT Key to scroll the second string of data of alarm
Zones;
than use the RIGHT Key to scroll the third string of data
of alarm causes;
than use the RIGHT Key to scroll the fourth string of
data of alarm Times and Events;
(*Note) If the event originates from a different control pa-
nel in the network, when this key is pressed the View LOG
for the control panel which produced the event will appear.
This symbol shows the presence
of the connection between the
Control panel status
User Interface and the Main Board
status: ALARM
EVAC.
zone=456
zone=245
This symbol shows
the presence of following
Point identification
blocks to be scrolled by Right cursor key,
the symbol shows the presence
of previous blocks to be scrolled by
Left cursor key.
status: ALARM
status:ALARM
zone: RD dept. First floor
zone: RD dept. First floor
zone: Power station area
Push the right key to scroll
the second block of data
regarding the ALARM zones
status: ALARM
det: office 3, south
det: main corridor, north
mod: air compressor room
Push the right key to scroll
the third block of data
regarding the ALARM causes
status: ALARM
EVAC.
Manual
Temp.
Push the right key to scroll
the fourth block of data
regarding the ALARM times
status: ALARM
- 01/01/07
- 01/01/07
- 01/01/07
1° block:
FC500