Important Safety Instructions; Installation Instructions - Cardin Elettronica GL Serie Manual Del Usuario

IMPORTANT REMARKS
TO REdUCE THE RISK OF SEVERE INJURY OR dEATH REAd THE FOLLOWING REMARKS CAREFULLY BEFORE
PROCEEdING WITH THE INSTALLATION. PAY PARTICULAR ATTENTION TO ALL THE PARAGRAPHS MARKEd
WITH THE SYMBOL
RECT WORKING ORdER OF THE SYSTEM.
• These instructions are aimed at professionally qualified
"INSTALLERS OF ELECTRICAL EqUIPMENT" and must
respect the local standards and regulations in force. All materi-
als used must be approved and must suit the environment in
which the installation is situated.
• All maintenance operations must be carried out by profession-
ally qualified technicians. Before carrying out any cleaning or
maintenance operations make sure the power is disconnected
at the mains.
• This appliance must be used exclusively for the purpose for
which it has been made. "i.e. The automation of garage
doors" Any non authorised modifications are to be considered
improper and therefore dangerous.
USE
The appliance may be used to operate a single or articulated garage
door. For garage doors with a width of over 4 m and not more than
2,7 m in height and for garage doors with a pedestrian access
door two motors are required (one motor with on board electronics
30/GLB242SWS and one without 30/GLB240SWS).
The manufacturer accepts no liability for situations arising from
an electrical installation which does not conform to the local
standards and regulations in force.

IMPORTANT SAFETY INSTRUCTIONS

It is the responsibility of the installer to make sure that the fol-
lowing public safety conditions are satisfied:
1) The pedestrian door must not open on its own, e.g.; swing
open while the garage door is in movement
2) The appliance must not be operated when the pedestrian door
is not fully closed.
3) Make sure that there are no dangerous sharp edges (R=3mm min.)
4) Make sure that the end-user is aware that children and/or pets
must not be allowed to play within the area of a garage door
installation. If possible include this in the warning signs.
5) A correct earth connection is fundamental in order to guarantee
the electrical safety of the machine
6) If you have any questions about the safety of the door operat-
ing system, do not install the operator. Contact your dealer for
assistance.
TECHNICAL dESCRIPTION
• Single piece geared reduction unit with an incorporated
encoder.
• 28 V direct current drive motor.
• Permanently lubricated double reduction unit mounted on a
cast iron stator with a never ending screw.
• Irreversible reduction unit with a key-operated manual release
mechanism.
• 30/GLB242SWS Motor with an incorporated electronic
programmer complete with power stage, logic control, battery
charger and radio receiver. Power is rooted to the card by a
separate toroidal transformer housed in the same container
and connected to the card
• 30/GLB240SWS motor without on board electronics
• Base in zinc-plated steel
• Carter in shock-proof plastic
• Courtesy light
IMPORTANT REMARKS
. NOT REAdING THESE IMPORTANT INSTRUCTIONS COULd COMPROMISE THE COR-
ACCESSORIES
36/GLO2Ad - Straight telescopic arm length 700 mm.
36/GLO3A - Curved (right) telescopic arm length 700 mm.
36/GLO4A - Curved (left) telescopic arm length 700 mm.
36/GLO6A - Straight telescopic arm length 1000 mm.
36/GLOPS - Motor support extension.
36/GLOTG - Pair of pipes, pipe support brackets and DIN
threaded pins for central motor positioning.
36/GLOCGL - Ferrule and DIN threaded pin, with pipe support
brackets for lateral motor positioning.
36/GL20SB - Manual release cord.
USER INSTRUCTIONS
During the opening/closing manoeuvre check for correct opera-
tion and activate the emergency stop button in case of danger.
The appliance must not be activated in the dark therefore make
sure that the night lights function correctly.
The appliance can be manually released in case of emergency
(see manual release mechanism on page 21).
Periodically check the moving parts for wear and tear and grease
if required, using lubricants which maintain their friction levels
unaltered throughout time and are suitable for temperatures of
-20 to +70°C. In case of failure or operational anomalies switch
off the power at the mains do not attempt to repair the appliance
yourself. Periodically check the correct operation of all safety
devices (photoelectric cells etc.).
Eventual repair work must be carried out by specialised person-
nel using original spare parts. The appliance is not suitable for
continuous operation and must be contained within the value
stipulated (see technical data on page 56).

INSTALLATION INSTRUCTIONS

The minimum controls which may be installed are SEQUEN-
TIAL-STOP, these controls must be installed in a location not
accessible to children.
Before starting with the installation of the system check that the
structure which is to be automated is in good working order and
respects the local standards and regulations in force.
Automating an existing system which has sliding or balancing
problems will not solve those problems and may even make them
worse by placing more stress on weakened or damaged areas.
To this end make sure that the runner guides slide freely and
grease all the moving parts (pins, castors etc.) using lubricants
which maintain unaltered friction characteristics over a period of
time and are suitable for temperatures of -20 to +70°C.
9
IMPORTANT REMARKS