Important Remarks - Cardin Elettronica GL Serie Manual Del Usuario

IMPORTANT REMARKS

REAd THE FOLLOWING REMARKS CAREFULLY BEFORE PROCEEdING WITH THE INSTALLATION.
PAY PARTICULAR ATTENTION TO ALL THE PARAGRAPHS MARKEd WITH THE SYMBOL
REAdING THESE IMPORTANT INSTRUCTIONS COULd COMPROMISE THE CORRECT WORKING
ORdER OF THE SYSTEM ANd CREATE dANGER SITUATIONS FOR THE USERS OF THE SYSTEM.
• These instructions are aimed at professionally qualified "INSTALLERS
OF ELECTRICAL EQUIPMENT" and must respect the local standards
and regulations in force. All materials used must be approved and must
suit the environment in which the installation is situated.
• All maintenance operations must be carried out by professionally qualified
technicians. Before carrying out any cleaning or maintenance operations
make sure the power is disconnected at the mains.
• This appliance must be used exclusively for the purpose for which it
has been made. "i.e. for the automation of counterbalanced garage
doors" Any non authorised modifications are to be considered improper
and therefore dangerous. The manufacturer accepts no liability for situ-
ations arising from an installation which does not conform to the local
standards and regulations in force.
IMPORTANT! The geared motor 310/GL2024 is not fitted with
a torque limiter. Only use an electronic programmer which has a
torque limiter with maximum force at the head of the gate equal
to 150N (local standards and regulations in force).
USE
The appliance may be used to operate single or articulated garage door of
up to 15m with a maximum weight of 100kg (central motor).
2
For garage doors with a width of over 4m and not more than 2,70m in height
(max. weight 180kg) and for garage doors with a pedestrian access door two
motors are required (one motor with electronics and one without).
310/GL20A
Self-locking electromechanical operator without on board electronics.
310/GL20AP08
Self-locking electromechanical operator with an incorporated programmer
automatic, semi-automatic, limited opening, torque limiter, electric locking
device and S486 decoder.
310/GL20AP09
Self-locking electromechanical operator with an incorporated programmer
automatic, semi-automatic, limited opening, torque limiter, electric locking
device and S449 decoder.
IMPORTANT SAFETY INSTRUCTIONS
It is the responsibility of the installer to make sure that the following public
safety conditions are satisfied:
1) The pedestrian door must not open on its own, e.g.; swing open while
the garage door is in movement
2) The appliance must not be operated when the pedestrian door is not fully
closed.
3) Make sure that there are no dangerous sharp edges (R=3mm min.)
4) Make sure that the end-user is aware that children and/or pets must not
be allowed to play within the area of a garage door installation. If possible
include this in the warning signs.
5) A correct earth connection is fundamental in order to guarantee the
electrical safety of the machine
6) If you have any questions about the safety of the gate operating system,
do not install the operator. Contact your dealer for assistance.
TECHNICAL dESCRIPTION
• Single piece geared reduction unit.
• Single phase drive motor with an incorporated overload protector and a
permanently lubricated reversible reduction unit mounted on a cast iron
stator.
• Manual release mechanism
• Base in zinc-plated steel
• Carter in shock-proof plastic
• Night light
ACCESSORIES
316/GLO2Ad - Straight telescopic arm length 700.
316/GLO3A - Curved (right) telescopic arm length 700.
316/GLO4A - Curved (left) telescopic arm length 700.
316/GLO6A - Straight telescopic arm length 1000.
316/GLOPS - Motor support extension.
316/GLOTG - Pair of pipes, pipe support brackets and DIN
threaded pins for central motor positioning.
316/GLOCGL - Ferrule and DIN threaded pin, with pipe support
brackets for lateral motor positioning.
316/GL20SB - Manual release cord.
IMPORTANT REMARKS
USER INSTRUCTIONS
Attention! Only for EU customers - WEEE marking.
This symbol indicates that once the products life-span has expired
it must be disposed of separately from other rubbish. The user
is therefore obliged to either take the product to a suitable dif-
ferential collection site for electronic and electrical goods or to
send it back to the manufacturer if the intention is to replace it
with a new equivalent version of the same product.
Suitable differential collection, environmental friendly treatment and disposal
contributes to avoiding negative effects on the ambient and consequently
health as well as favouring the recycling of materials. Illicitly disposing of this
product by the owner is punishable by law and will be dealt with according
to the laws and standards of the individual member nation.
During the opening/closing manoeuvre check for correct operation and acti-
vate the emergency stop button in case of danger. The appliance must not be
activated in the dark therefore make sure that the night lights function correctly.
The appliance can be manually released in case of emergency (see manual
release on page 17). Periodically check the moving parts for wear and tear and
grease if required, using lubricants which maintain their friction levels unaltered
throughout time and are suitable for temperatures of -20 to +70°C.
Periodically check the correct operation of all safety devices (photoelectric
cells etc.). Eventual repair work must be carried out by specialised person-
nel using original spare parts. The appliance is not suitable for continuous
operation and must be contained within the value stipulated (see technical
data on page 36).
INSTALLATION INSTRUCTIONS
The minimum controls which may be installed are OPEN-STOP-CLOSE, these
controls must be installed in a location not accessible to children. Before
starting with the installation of the system check that the structure which is
to be automated is in good working order and respects the local standards
and regulations in force. Automating an existing system which has sliding or
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by
balancing problems will not solve those problems and may even make them
worse by placing more stress on weakened or damaged areas. To this end make
sure that the runner guides slide freely and grease all the moving parts (pins,
castors etc.) using lubricants which maintain unaltered friction characteristics
over a period of time and are suitable for temperatures of -20 to +70°C.
FITTING THE UNIT
Fitting the motor centrally
1) Remove the motor from its positioning base "A" fasten the two motor base
extensions "B" to the positioning base. Mark the position of the motor axis
on the positioning base "A" and fasten the complete profile "A" and "B" to
the cross piece of the garage door. The motor axis must be 70 mm below
the hinged point of the door arm "C". (for non flush fitting garage doors) or
half way up for flush fitting garage doors (see figs 2-3). The motor support,
complete with its extensions, must be fitted to the side of the lock and has
to cover at least three cross pieces "d", "E" and "F" using a minimum of
three Ø 5mm rivets for each cross piece.
B
A
230mm
B
15
IMPORTANT REMARKS
. NOT
G
d
E
70mm
N
M
F
L
9
H
C