Function Modes - Cardin Elettronica GL Serie Manual Del Usuario

B - Cancelling a channel (fig.10):
1. Press and hold down the button "P3" DELETE: The LED "L2" will flash
quickly.
2. Activate the transmitter channel which is to be cancelled.
3. The LED "L2" will remain lit for 2 seconds, indicating that the transmitter
has been cancelled.
Note: If the user that you wish to cancel is not in memory, The LED will stop
flashing; Only after releasing the button "P3" will you be able to continue
the cancellation procedure. For both the memorisation and cancellation
procedures, if the button is released before activating the transmitter the
procedure will abort.
C - Cancelling all user codes from memory (fig. 10):
1. Keep both buttons pressed down ("P2+P3") for more than 4 seconds
2. LED "L2" will remain lit during the entire cancellation time (about 8 s).
3. LED "L2" switches off when the cancellation procedure has terminated.
Note: When the memory is almost full the time required to search for a user
code could take up to 1 second from when the command was received. If
led "L2" remains alight memory is completely full.
To memorise a new transmitter you will first have to cancel a code from
memory.
d) Memorising ulterior channels via radio
• Memorisation can be activated by radio (without opening the receiver
container) if jumper "J2" has been inserted (fig.12).
1) Make sure that the jumper "J2" has been inserted (fig.12).
2) Using a transmitter, in which at least one channel button "A,B,C or D" has
already been memorised in the receiver, press the button on the transmitter
as shown in figure below.
Note: all the receivers within range when the channel button is pressed
(and which have at least one of the transmitter channel buttons memorised)
will activate their signal buzzer "B1" (fig.
12).
3) Press one of the channel buttons on
the same transmitter. The receivers
which do not contain that channel code
will sound a five-second long "beep"
and will then deactivate. The receivers
which contain the channel code will sound a one-second long "beep"
and will enter the programming mode.
4) Press the previously chosen channel buttons on the transmitter which
you wish to memorise; the receiver will sound 2 "beeps" of half a second
each after which the receiver will be ready to receive another code.
5) To leave the programming mode wait for 5 seconds without pressing any
buttons. The receiver will sound a five-second long "beep" and will then
exit the programming mode.
Note: When the memory is entirely occupied the buzzer will sound 10 rapid
"beeps" and will automatically leave the "programming via radio" mode.
Led "L2" will remain lit on the receiver. The same signal is given each time
you try to enter "programming via radio" when the memory is full.
CONNECTING THE ANTENNA
The receiver is supplied with its own antenna which consists of a piece of
rigid wire 170 mm in length. In alternative it is possible to connect an ANS400
(S449) - ANS800 (S486) tuned antenna using a coaxial cable RG58 (imped-
ance 50Ω) with a maximum length of 15 m.

FUNCTION MOdES

Functions selected using the Dip-switch "S2"
Pos. A (Dip 1 "ON" + Dip 2 "ON")
Automatic reclosing + limited dynamic button mode using the sequence
"Open- Close" (with travel direction inversion only during the closing
stage)
Pos. B (Dip 1 "OFF" + Dip 2 "OFF")
Automatic reclosing excluded + normal
dynamic button mode using the sequence
"Open-Block-Close-Block"
Pos. C (Dip 1 "ON" + Dip 2 "OFF")
Automatic reclosing excluded + limited
dynamic button mode using the sequence
"Open- Close" (with travel direction inversion
only during the closing stage)
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
Description : MEMORIZZAZIONE COdICE Tx-Rx
Drawing number :
dM0531
Product Code : RCQ449100
Draft : P.J.Heath Date : 13-04-2001
CARdIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Pos. d (Dip 1 "OFF" + Dip 2 "ON")
Automatic reclosing + normal dynamic button mode using the sequence
"Open-Block-Close-Block"
1) Automatic
Selected by moving dip 2 to the "ON" position. When the door is completely
closed the opening command will start a complete cycle consisting of open-
ing and automatic reclosing. Thirty seconds after the door is completely
closed the timer will switch off the night lights.
Automatic reclosing starts after the programmed pause period has elapsed
when the opening cycle has been completed or straight away after the
intervention of a photoelectric cell (the intervention of a photoelectric cell
causes the pause time to be reset).
Note: The night light switches on automatically each time a movement
command is given either by control button or by radio. The intervention
of a photoelectric cell during reclosing has no effect on the timing of the
night light.
2) Semi-automatic
Selected by moving dip 2 to the "OFF" position. Work cycle control using
separate opening and closing commands. When the door has reached the
completely open position the system will wait, until it receives a closing
command either via an external control button or via radio control, before
completing the cycle. Starting from the opening manoeuvre the night light
will switch off after the following period has elapsed: pause time + closing
time + 30 seconds.
ALARM CONdITIONS
1) Work time loaded from EEPROM is wrong
LED "L1" will flash and the system remains blocked.
The only way to solve this situation is enter the program mode and repro-
gram the system. If the problem persists after reprogramming, the EEPROM
will have to be replaced.
2) Both travel limits have cut-in
The system blocks as it is impossible to function in this condition.
This situation is indicated by the periodical activation of the flashing
warning lamps which are activated for 3 second periods repeated every
6 seconds.
The only way to solve this problem is to check the travel limits for obstacles
or damage and then restart the system.
Operation without using mechanical closing travel limits
The system is designed to operate without mechanical closing travel
limits; the work time management allows the system to control the posi-
tion of the garage door. The following points however should be taken
into consideration:
- during blackouts the programmer will lose the position of the garage
door and it will be assumed to be completely closed.
- after the first impulse when the power has returned the garage door will
only move in the opening direction after which it will function normally.
- a successive impulse with dip1 in the "OFF" position will block all
movement and another impulse will then send the door in the closing
direction.
- once the opening travel limit has been reached the door can automati-
cally reclose if the function has been chosen. (pos. A or D in the first
paragraph of the "function modes" section.
- once the opening travel limit has been reached the door can reclose
after the next impulse if the semi-automatic function has been chosen.
(pos. B or C in the first paragraph of the "function modes" section.
Electric lock functions
The electric locking device only activates during opening and reopening.
This occurs for each movement command given after start up until the door
is completely closed. From this point onwards the electric lock will only
activate when the door is in proximity with the completely closed position
(thus avoiding unnecessary activation).
19