Silverline 255234 Traducción Del Manual Original página 13

• If this is not sufficient, use warm water with a mild pH neutral (pH 7) detergent to clean off any
foreign matter. Dry thoroughly and lubricate moving parts with a suitable spray lubricant.
• DO NOT under any circumstances use any abrasive materials, acids, basic detergents or
solvents.
• Disinfect parts that come into contact with the operator's skin, using a disinfectant suitable for
the material of the equipment (see 'Specification') and not known to cause irritation to the user.
Strictly follow the disinfectant manufacturer's recommendations and procedures.
• ALWAYS allow the equipment to dry naturally and keep it away from open fires or any other
heat sources. Ensure area beneath Energy Absorber sheath is thoroughly dry before returning
the equipment to use or storage.
Note: This also applies to equipment that has become wet during use.
Lubrication
• Occasionally apply a small amount of a suitable spray lubricant to the Gate (17, 25)
mechanism. Afterwards, perform a thorough inspection as described in 'Inspection procedure'
Transport
• ALWAYS transport this equipment inside a dedicated bag or suitable container that protects it
from mechanical damage and shields the equipment from high temperatures, humidity, UV
rays and chemicals.
Storage
• Store this equipment carefully in a secure, dry place out of the reach of children
• Store at moderate temperature and humidity, away from direct sunlight or chemicals, inside a
dedicated, UV-proof bag or container
• Never place heavy objects on top of this equipment
Disposal
Service life and product obsolescence
WARNING: Fall arrest equipment and related restraint or work positioning equipment is
designed to arrest a fall from height ONLY ONCE! If subjected to an arrested fall, the gear must be
withdrawn from service and rendered unusable.
Note: The date on which the product is removed from the original packaging for the first time
becomes the 'date of first use', which should be recorded on the Inspection Record (see end of this
manual). The specified working life begins from this point.
• Due to the ingress of dirt and grit, chemical contamination, edge and surface damage, UV-light
degradation and general wear and tear, all fall arrest, work positioning and restraint equipment
manufactured from synthetic fibres (webbing and/or rope) is subject to a manufacturer's
statement of obsolescence, which is a requirement of BS EN 365:2004.
• This equipment is subject to a maximum working life of 5 years from the recorded date of first
use, providing the product has been correctly stored, maintained and subjected to regular
inspections by a trained and competent person.
• New equipment may be stored for a maximum of 5 years from the date of manufacture, as
indicated on the product, and will still give the potential 5-year working life – providing it
remains in the original manufacturer's packaging and is used and stored in accordance with
the instructions provided.
• If the new product is stored for longer than 5 years unopened from the date of manufacture,
the maximum remaining working life will be reduced up until 10 years from the date of
manufacture, as indicated on the product. For example, if the product is stored new and
unopened for 7 years then it is opened and used, the maximum working life of the equipment
will be the remaining 3 years.
Note: Other reasons why the product may be considered obsolete include, but are not limited to,
changes of applicable standard, regulations or legislation, development of new techniques, or
incompatibility with other equipment.
WARNING: Remove height safety equipment from service if:
• It has been used to arrest a fall
• Any damage is present (including corrosion and rust)
• Identification is not evident (permanent markings are not legible or have been damaged/
removed)
• It exceeds its specified service life
• Its full service history is unknown
• You have any doubt as to its integrity
Contact
Legal Manufacturer: Toolstream Ltd
For Declaration of Conformity please visit www.silverlinetools.com
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: www.silverlinetools.com
UK Address:
Toolstream Ltd.
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
Approved body: CCQS UK (1105), 5 Harbour Exchange Square London, E14 9GE, United Kingdom
Approved body number: 1105
EU Address:
Toolstream B.V.
Holtum-Noordweg 11
Unit 4
6121 RE Born
The Netherlands
Notified body: CCQS Certification Services Limited, Block 1 Blanchardstown Corporate Park,
Ballycoolin Road, Blanchardstown, Dublin, D15 AKK1, Ireland
Notified body number: 2834
WARNING: If the product is re-sold outside the original country of destination, it is essential
the reseller shall provide instructions for use, periodic examination, maintenance and repair in the
language of the country in which the product is to be used.
silverlinetools.com
Fall Arrest Kit 5pce
13