Bosch Professional GTS 10 J Manual Original página 43

– Tighten the adjusting screw (24) until the parallel guide
can be securely fixed to the saw table again.
Adjusting the magnifying glass of the parallel guide (see
figure M)
– Bring the power tool into the work position.
– Remove the blade guard (6).
– Move the parallel guide (9) from the right until it touches
the saw blade.
Checking
The marking in the magnifying glass (27) must be in line with
the 0 mm mark on the scale (2).
Setting
– Loosen the screw (67) using a cross-headed screwdriver
and align the marking along the 0 mm mark.
Adjusting the level of the table insert (see figure N)
Checking
The front side of the table insert (25) must lie flush with or a
little below the saw table; the rear must lie flush with or a
little above the saw table.
Setting
– Remove the table insert (25).
– Use the hex key (21) to set the correct level of the four
adjusting screws (68).
Storage and transport
Storing tool elements (see figures O1–O5)
You can attach certain tool elements to the power tool to
store them.
– Detach the additional parallel guide (41) from the parallel
guide (9).
– Place all loose components of the tool in their storage
compartments on the housing (see the following table).
Fig- Tool element Storage compartment
ure
O1 Protective cover Place in the recess on the
bracket (33) and secure using
the clamping lever (37)
O2 "Additional parallel Clip into the brackets (69)
guide" fastening set
(42)
O2 Dust extraction ad- Slide into the holding clips (70)
apter (32)
O3 Ring spanner (22) Secure in the storage compart-
ment using the securing nut
(71)
O3 Push stick (23) Suspend using the securing nut
(71) and slide to secure
O4 Parallel guide (9) Turn around, suspend from be-
low in the guide rails and secure
the clamping handle (39)
O5 Hex key (21) Slide into the brackets (72)
Hex key (20)
O5 Angle guide (3) Slide into the holding clips (73)
Bosch Power Tools
Fig- Tool element Storage compartment
ure
O5 Additional parallel Slide into the holding clips (30)
guide (41) (short side facing up, long side
facing the rear)
Transporting the power tool
Before transporting the power tool, the following steps must
be carried out:
– Bring the power tool into the transport position (see
"Transport position", page 39).
– Remove all accessories that cannot be securely fitted to
the power tool.
If possible, transport unused saw blades in a closed con-
tainer.
– Slide the saw table expansion (13) in fully and push the
clamping handle (15) down to secure it in place.
– Wrap the power cable around the cable holder (29).
– Use the carrying handles (12) to lift or transport the tool.
Only use the transport devices to transport the power
u
tool and never the protective devices.
Maintenance and servicing
Maintenance and cleaning
Pull the plug out of the socket before carrying out any
u
work on the power tool.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
Cleaning
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
Remove dust and chippings after each operation with a
paintbrush.
Lubricating the power tool
Lubricant:
SAE 10/SAE 20 engine oil
– Oil the power tool as necessary at the points
indicated (see figure P).
An authorised Bosch after-sales service point will handle this
work quickly and reliably.
Dispose of lubricants and cleaning products in an envir-
onmentally friendly manner, taking legal regulations into
account.
Noise reduction measures
Measures implemented by the manufacturer:
– Soft start
– Provided with a saw blade specially developed for noise
reduction
Measures implemented by the operator:
– Low-vibration mounting on a stable work surface
English | 43
1 609 92A 5C2 | (26.07.2019)