Idiomas disponibles
Idiomas disponibles
ENG ORIGINAL INSTRUCTIONS
PERSONAL SAFETY.
Stay alert, watch what you are doing and use com-
mon sense when operating a power tool. Do not
use a power tool while tired or under the influence
of drugs, alcohol or medicines. A moment of inat-
tention while operating power tools may cause da-
mage serious personal.
USE PPE'S.
Use protection glasses according to EN166.
Use protection helmet according to EN397. Use
protection gloves according to EN388 (minimal
levels 2). Use protection shoes according to EN
ISO 20345:2011 (minimal level SB). If required by
the type of work, use other precise PPE.
DO NOT WORK ON TIPTOES.
Keep your feet on the ground and balance at all ti-
mes. This enables better control of the power tool in
unexpected situations.
DRESS PROPERLY.
Do not wear loose clothing or jewelry. Keep your
hair, clothing and gloves away from moving parts.
Loose clothes, jewelry or long hair can be caught
in moving parts. If there are devices for connecting
means for extracting and collecting dust, make sure
they are connected and properly used. The use of
these devices can reduce dust related hazards.
ELECTRICAL SAFETY.
The plug of the power tool must match with the base
of the socket . Never modify the plug in any way . Do
not use any adapter plug with earthed power tools .
Unmodified plugs and matching bases will reduce
the risk of electric shock . Avoid body contact with
grounded surfaces such as pipes, radiators, cookers
and refrigerators . There is an increased risk of elec-
tric shock if your body is grounded . Do not expose
power tools to rain or wet conditions . Water entering
the power tool will increase the risk of electric shock.
DO NOT ABUSE THE CORD.
Never use the cord to carry, lift or unplug the power
tool . Keep the cord away from heat, oil, sharp edg-
es or moving parts . Damaged or entangled cords
increase the risk of electric shock . When operating
a power tool outdoors, use an extension cord suit-
able for outdoor use . The use of an extension cord
suitable for outdoor use reduces the risk of electric
shock . If the use of a power tool in a damp loca-
tion is unavoidable, use a power protected by a
residual current device (RCD) . The use of an RCD
reduces the risk of electric shock.
AVOID ACCIDENTAL STARTING.
Make sure the switch is in "off" position before con-
necting to the network, or when taking or carrying
the power tool. Carrying power tools with your fin-
ger on the switch or plugging in power tools that
have the switch in "on" position invites to acci-
dents. Remove keys or tools before starting the
power tool. A left key or tool attached to a rotat-
ing part of a power tool can cause personal injury.
Never lay this power tool down until the accessory
has come to a complete stop. The spinning acces-
sory may grab the surface and pull this power tool
out of your control. Do not run this power tool while
carrying it at your side. Accidental contact with the
spinning accessory could snag your clothing, pull-
ing the accessory into your body.
USE AND CARE OF POWER TOOLS.
Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
conceived. Do not use the power tool if the switch
cannot be positioned to "off" and "on" position. Any
power tool that cannot be controlled with the switch is
dangerous and must be repaired. Remove the plug
from the power supply and/or battery before making
any adjustments, changing accessories or storing
the power tool. Such preventive safety measures re-
duce the risk of starting the power tool accidentally.
Do not use accessories which are not specifically de-
signed and recommended by Werku
the accessory can be attached to this power tool, it
does not assure safe operation. The rated speed of
the accessory must be at least equal to the maximum
speed marked on this power tool. Accessories run-
ning faster than their rated speed can break and fly
apart. The outside diameter and the thickness of your
accessory must be within the capacity rating of this
power tool. Incorrectly sized accessories cannot be
adequately guarded or controlled. Threaded mount-
ing of accessories must match the spindle thread.
For accessories mounted by flanges, the arbour hole
of the accessory must fit the locating diameter of the
flange. Accessories that do not match the mounting
hardware of this power tool will run out of balance,
vibrate excessively and may cause loss of control.
Do not use a damaged accessory. Before each use,
inspect the accessory. If this power tool or its acces-
sory is dropped, inspect for damage or install an un-
damaged accessory. After inspecting and installing
an accessory, position yourself and bystanders away
from the plane of the rotating accessory and run this
power tool at maximum no-load speed for one min-
3
English
. Just because
®
