DeWalt DCS365 Traducido De Las Instrucciones Originales página 48

english
ALTERNATIVE METHOD FOR CUTTING CROWN MOLDING
Place the molding at an angle between the fence (K) and the saw table
(AQ), as shown in Figure 21.
The advantage to cutting crown molding using this method is that no bevel
cut is required. Minute changes in the mitre angle can be made without
affecting the bevel angle. This way, when corners other than 90º are
encountered, the saw can be quickly and easily adjusted for them.
INSTRUCTIONS FOR CUTTING CROWN MOLDING ANGLED BETWEEN THE FENCE AND
BASE OF THE SAW FOR ALL CUTS
This saw can cut up to 14 mm (9/16") x 92 mm (3-5/8") crown molding
nested.
1. Place the molding at an angle between the fence (K) and the saw table
(AQ), as shown in Figure 21.
2. The angled "flats" on the back of the molding must rest squarely on the
fence and saw table.
INSIDE CORNER
Mitre right at 45°
Left side
Save right side of cut
Mitre left at 45°
Right
side
Save left side of cut
Special Cuts
NEVER MAKE ANY CUT UNLESS THE MATERIAL IS SECURED ON
THE TABLE AND AGAINST THE FENCE.
BOWED MATERIAL (FIG. 22, 23)
When cutting bowed material always position it as shown in Figure 22 and
never like that shown in Figure 23. Positioning the material incorrectly will
cause it to pinch the blade near the completion of the cut.
CUTTING ROUND MATERIAL
ROUNDED MATERIAL SHOULD BE CLAMPED OR HELD FIRMLY TO
THE FENCE TO KEEP IT FROM ROLLING. This is extremely important
when making angle cuts.
CUTTING LARGE MATERIAL (FIG. 24)
Occasionally you will encounter a piece of wood a little too large to fit
beneath the lower guard. To clear the guard over the wood, with the
saw off and your right hand on the operating handle, place your right
thumb outside of the upper portion of the guard and roll the guard up
just enough to clear the wood, as shown in Figure 24. Release the guard
prior to starting the motor. The guard mechanism will function properly
during the cut. Only do this when necessary. NEVER TIE, TAPE, OR
OTHERWISE HOLD THE GUARD OPEN WHEN OPERATING THIS SAW.
MAINTENANCE
Your D WALT power tool has been designed to operate over a long period
e
of time with a minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack before
making any adjustments, performing any cleaning or
maintenance, or removing/installing attachments or
accessories. An accidental start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of the main housing with
dry air as often as dirt is seen collecting in and around the air
vents. Wear approved eye protection and approved dust mask
when performing this procedure.
46
OUTSIDE CORNER
Mitre left at 45°
Save right side of cut
Mitre right at 45°
Save left side of cut
WARNING: Never use solvents or other harsh chemicals for
cleaning the non-metallic parts of the tool. These chemicals
may weaken the materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool into a
liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect the charger from the AC
outlet before cleaning. Dirt and grease may be removed from
the exterior of the charger using a cloth or soft non-metallic
brush. Do not use water or any cleaning solutions.
Optional Accessories
WARNING: Since accessories, other than those offered by
D WALT, have not been tested with this product, use of such
e
accessories with this tool could be hazardous. To reduce the
risk of injury, only D WALT recommended accessories should
e
be used with this product.
The following accessories, designed for your saw, may be helpful.
In some cases, other locally obtained work supports, length stops,
clamps, etc., may be more appropriate. Use care in selecting and using
accessories. Consult your dealer for further information on the appropriate
accessories.
SAW BLADES
ONLY USE 184 mm (7-1/4") SAW BLADES WITH 16 mm (5/8")
DIAMETER ROUND ARBOR HOLES and a maximum KERF of 2.1 mm
(0.08"). SPEED RATING MUST BE AT LEAST 4000 RPM. DO NOT
USE BLADES WITH DIAMOND-SHAPED ARBOR HOLES. Never use
a different diameter blade. It will not be guarded properly. Use crosscut
blades only! Do not use blades designed for ripping, combination blades
or blades with hook angles in excess of 7°.
BLADE DESCRIPTIONS
APPLICATION
General Purpose 184 mm (7-1/4")
Fine Woodcutting 184 mm (7-1/4")
Protecting the Environment
Separate collection. Products and batteries marked with this
symbol must not be disposed of with normal household waste.
Products and batteries contain materials that can be recovered or
recycled reducing the demand for raw materials. Please recycle
electrical products and batteries according to local provisions.
Further information is available at www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails to produce
sufficient power on jobs which were easily done before. At the end of its
technical life, discard it with due care for our environment:
• Run the battery pack down completely, then remove it from the tool.
• Li-Ion cells are recyclable. Take them to your dealer or a local recycling
station. The collected battery packs will be recycled or disposed of
properly.
DIAMETER TEETH
40
60