Noise Information; Items Included; Fitting Individual Components - Bosch GTS 10 XC Professional Manual Original

38 | English
Table saw
Overload protection
Weight according to EPTA-Procedure
01:2014
Protection class
Dimensions (including detachable parts of the tool)
Width x depth x height
Dimensions of suitable saw blades
Saw blade diameter
Base blade thickness
Min. tooth thickness/offset
Hole diameter
Maximum workpiece dimensions: (see "Maximum workpiece dimensions", page 43)

Noise information

Noise emission values determined according to
EN 62841-3-1.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 92 dB(A); sound power level
105 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
The noise emission value given in these instructions has
been measured in accordance with a standardised measur-
ing procedure and may be used to compare power tools. It
may also be used for a preliminary estimation of noise emis-
sions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used
for other applications, with different application tools or is
poorly maintained, the noise emission value may differ. This
may significantly increase noise emissions over the total
working period. To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
ficantly reduce noise emissions over the total working
period.
Assembly
Avoid starting the power tool unintentionally. The
u
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
work on the power tool.

Items included

Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
List of items included
– Table saw with fitted saw blade (33) and riving knife (7)
– Angle guide (3)
– Profile rail (34)
– "Profile rail" fastening set (55) (guide plate, knurled nut,
screw, washer)
1 609 92A 7WN | (14.06.2022)
GTS 10 XC
kg 35,0
mm 810 x 768 x 343
mm 254
mm <2.2
mm > 2.4
mm 25.4
– Parallel guide (8)
– Additional parallel guide (52)
– "Additional parallel guide" fastening set (39) (3 fastening
screws, 3 washers, 3 wing nuts)
– Protective cover (6)
– Table extension (10)
– "Table extension" fastening set (43) (2 fastening screws,
2 washers, 1 open-ended spanner)
– Hex key (37)
– Ring spanner (15)
– Saw blade storage compartment cover (14)
– Push stick (13)
– Table insert (32)
– Dust extraction adapter (41)
Note: Check the power tool for possible damage.
Before continuing to use the power tool, carefully check that
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
ised service centre.
Extra tools required (not included in the delivery):
– Slotted screwdriver
– Cross-headed screwdriver
– Angle gauge

Fitting individual components

– Carefully remove all parts included in the delivery from
their packaging.
– Remove all packing material from the power tool and the
accessories provided.
– Open the base grid (45) and remove the packaging ma-
terial underneath the motor block (see figure a).
GTS 10 XC
●
35,0
/ II
810 x 768 x 343
254
<2.2
> 2.4
25.4
Bosch Power Tools
●
/ II